Members superpacker Posted May 14, 2018 Members Report Posted May 14, 2018 (edited) When I've sew two pieces together, and after going through beveling, sanding, burnishing, dyeing (and some re-burnishing) I am getting nice slick edges. However, my one concern is that it seems like no matter what I do, you can see a faint line down the center of my dyed edges where two pieces are sewn together. Is there anyone way to better eliminate this line and more fully make it look like a single, uniform edge? Edited May 14, 2018 by superpacker Quote
Members cradom Posted May 14, 2018 Members Report Posted May 14, 2018 Are the two pieces glued? Contact cement helps keep the edges together. Quote
Members superpacker Posted May 14, 2018 Author Members Report Posted May 14, 2018 They are glued. But to avoid it spilling over onto the edge when clamped I try not to take it to the end of the edge Quote
Members cradom Posted May 15, 2018 Members Report Posted May 15, 2018 Take it all the way to the edge. Leaving it shy of the edge wont let the leather edges stick together and will show the line. Quote
Contributing Member JLSleather Posted May 15, 2018 Contributing Member Report Posted May 15, 2018 You wont entirely eliminate the "line". But DO glue to the edge. In fact, I generally glue the back of the belt, then cut the liner about 1/4" wider so I don't have to "fiddle" with lining it up. Stick'er down, tap the edges, trim. If you got any "glue boogers", a piece of canvas will take it off easily.. no water, just rub the edge with canvas (I'm told denim will work also). To avoid "bits" I didn't see, I just rub the entire edge - take bout a minute. You can POLISH that edge to no end, and you will STILL have a thin "line" (but no space between layers). Quote "Observation is 9/10 of the law." IF what you do is something that ANYBODY can do, then don't be surprised when ANYBODY does.
Moderator immiketoo Posted May 16, 2018 Moderator Report Posted May 16, 2018 23 hours ago, JLSleather said: You wont entirely eliminate the "line". But DO glue to the edge. In fact, I generally glue the back of the belt, then cut the liner about 1/4" wider so I don't have to "fiddle" with lining it up. Stick'er down, tap the edges, trim. If you got any "glue boogers", a piece of canvas will take it off easily.. no water, just rub the edge with canvas (I'm told denim will work also). To avoid "bits" I didn't see, I just rub the entire edge - take bout a minute. You can POLISH that edge to no end, and you will STILL have a thin "line" (but no space between layers). I HATE the line. I have spent a lot of time learning to eliminate the line. With enough sanding, slicking and wax you CAN eliminate the line. Most people won't take the time to do the work required to eliminate it, but I refuse to let them live in my work. Quote Learnleather.com
Members Bolt Vanderhuge Posted May 17, 2018 Members Report Posted May 17, 2018 (edited) On 5/16/2018 at 10:49 AM, immiketoo said: I HATE the line. I have spent a lot of time learning to eliminate the line. With enough sanding, slicking and wax you CAN eliminate the line. Most people won't take the time to do the work required to eliminate it, but I refuse to let them live in my work. This works for me too. You just have to put in the time both in prep work before edging and then when finishing the edges. By putting in the little bit of extra time you can make 4 layers of leather have no visible line. Edited May 17, 2018 by Bolt Vanderhuge Quote
Members jcuk Posted May 17, 2018 Members Report Posted May 17, 2018 Here is is a quick video of a method i have used on my work not sure if it would work for but you can give try on some scrap leather. I also work mainly on horse tack, a lot heavier weight leather than the leather in your photo - correct me if i am wrong a watch strap thats why As I say, not sure if it would work for you. JCUK Hope this helps JCUK Quote
Moderator immiketoo Posted May 17, 2018 Moderator Report Posted May 17, 2018 1 hour ago, Bolt Vanderhuge said: This works for me too. You just have to put in the time both in prep work before edging and then when finishing the edges. By putting in the little bit of extra time you can make 4 layers of leather have no visible line. One thing about this. Using your contact cement properly is crucial. Thin glue is better than thick gobs of it, and its imperative that you hammer all your edges with a cobblers hammer. This compresses the fibers and helps make the composite as close to one piece of leather. The hammering step changed my world when it came to eliminating the line, but to see it now you'd need a good magnifying glass and very bright light at precisely the right angle, and even then, most people miss it. Quote Learnleather.com
Contributing Member JLSleather Posted May 17, 2018 Contributing Member Report Posted May 17, 2018 No dye. No edge poop. No liquid plastic. Just leather 'n' glue ... ''n' no line. Nope. I mean eliminate it, not camouflage it. Quote "Observation is 9/10 of the law." IF what you do is something that ANYBODY can do, then don't be surprised when ANYBODY does.
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.