3D printer recommendations

[MY63]

Hi 

I am looking for an entry level 3D printer for making small items such as a one off stamp or small mould for leather work.

thanks in advance

[jpounders95]

The tevo tarantula, anet A8, or the creality 3d ender would all be good choices and all are under $200 on gearbest

 

[dikman]

I have a Tarantula and it works well enough BUT it comes as a kit and needed a bit of work to get it working properly. If you want to just plug it in and print do not get a kit. If, however, you like a challenge (and knocking your head against a brick wall!) and want to learn how these beasties work then a kit is the way to go.

[jpounders95]

 The ones I mentioned above are all kits btw sorry I forgot that! If you want plug and play you might look at the M3D micro+ or the XYZ Da Vinci or da vinci jr they are all reasonably priced (under $350 i believe) and do the job fairly well after playing with them

[bullmoosepaddles]

@jpounders95 I also am thinking about getting one soon. Definitely want a plug and play. What do you mean by "do the job fairly well after playing with them"?

[jpounders95]

The quality of the print ranges from what material you use and what settings you use on it. IE: playing with the bed temperature and the nozzle temperature as well as the feed rate to get it to lay down the smoothest layers possible 

[veedub3]

I purchased an Anet 8, and after watching tons of videos and reading tons of post on the FB group page on what I needed to buy and or print to make the unit more sturdy/reliable I sold it and purchased a Monoprice Select 2 for about $250 off Amazon. Took less than 5 minutes to set up and I was printing my test print. Had it well over a year and no complaints. I don't have anything against kits, My CNC Machine was a kit. (X-Carve), but it just seemed like there was a ton of work and mods needed for the Anet 8 Kit and I just decided a plug an play would serve me better. YMMV

Karina

[MY63]

@jpounders95 Thanks for the suggestions as @dikman said I am done with banging my head against a brick wall I would really like plug and play where possible a little assembly is ok.

I have done some research on line and have a couple of specifications I would like the first being a heated bed and the second is the ability to use A B S along with other filaments.

@veedub3 your recommendation looks perfect I would like to make single use stamps and maybe the odd mould for leather in your experience is that possible with this printer.

Thanks everyone

Michael

[veedub3]

On 8/19/2018 at 12:12 PM, MY63 said:

 

@veedub3 your recommendation looks perfect I would like to make single use stamps and maybe the odd mould for leather in your experience is that possible with this printer.

Thanks everyone

Michael

Yes, it is possible with this machine and I have done both with success. I used my 3D printer all the time for this until I got my CNC machine. Now I make those items using HDPE and or Delrin that will hold up much, much longer, in a fraction of the time. My 3D printer is now used to make the odd part I need that I can't just go out and purchase. For what you are wanting  to do, it will definitely do the job, and the learning curve is not too bad.

Karina

[MY63]

2 hours ago, veedub3 said:

Yes, it is possible with this machine and I have done both with success. I used my 3D printer all the time for this until I got my CNC machine. Now I make those items using HDPE and or Delrin that will hold up much, much longer, in a fraction of the time. My 3D printer is now used to make the odd part I need that I can't just go out and purchase. For what you are wanting  to do, it will definitely do the job, and the learning curve is not too bad.

Karina

Thanks Karina I appreciate you help