Jump to content

Recommended Posts

  • Members
Posted

What would cause my presser foot to stay in the up position after using the knee lift or the hand lever? I can release it if I press very hard on the top of the foot. 

Consew 206RB-1

Thanks!

Sewing Machines:

Consew 206RB-1

  • Contributing Member
Posted

A little bitty metal bur.

Ferg

  • Members
Posted

Might need a few drops of oil from above.  Sometimes machines do this temporarily, if they've been sitting unused for too long.  Other times you have a bent part.  

More times than not, a liberal oiling will free it up.  

One quick test to rule out the feet as a potential source... Remove the feet and re-test the lifting action.  If the problem remains, it's the articulations in the head at fault.  

  • Moderator
Posted

An out of round hole in the pressure adjuster screw will cause the foot bar to hang until you rotate it to the right position. Also, add more pressure to overcome the out of round condition.

Posted IMHO, by Wiz

My current crop of sewing machines:

Cowboy CB4500, Singer 107w3, Singer 139w109, Singer 168G101, Singer 29k71, Singer 31-15, Singer 111w103, Singer 211G156, Adler 30-7 on power stand, Techsew 2700, Fortuna power skiver and a Pfaff 4 thread 2 needle serger.

  • Members
Posted

See attached, it's likely the knee stopper highlighted index 2 is making contact before the knee lifter mechanism on the machine is.  

Also, the thrusting bar as they call it may be hitting and stopping at the bell crank, making it more like you are lifting the machine out of the stand rather than continuing to lift the bell crank up under the  machine.

KNeeLifterEndPointAdj.jpg

Industrial sewing and cutting, parts sales and service, family owned since 1977, Philadelphia, Pennsylvania USA, 215/922.6900 info@keysew.com www.keysew.com

  • Members
Posted
11 hours ago, Pintodeluxe said:

Might need a few drops of oil from above.  Sometimes machines do this temporarily, if they've been sitting unused for too long.  Other times you have a bent part.  

More times than not, a liberal oiling will free it up.  

One quick test to rule out the feet as a potential source... Remove the feet and re-test the lifting action.  If the problem remains, it's the articulations in the head at fault.  

It still sticks after removing the feet. Can you be more specific on the articulations in the head being at fault?

11 hours ago, Wizcrafts said:

An out of round hole in the pressure adjuster screw will cause the foot bar to hang until you rotate it to the right position. Also, add more pressure to overcome the out of round condition.

Thanks, Wiz. I will try that as well. 

Sewing Machines:

Consew 206RB-1

  • Members
Posted
16 minutes ago, Gregg From Keystone Sewing said:

See attached, it's likely the knee stopper highlighted index 2 is making contact before the knee lifter mechanism on the machine is.  

Also, the thrusting bar as they call it may be hitting and stopping at the bell crank, making it more like you are lifting the machine out of the stand rather than continuing to lift the bell crank up under the  machine.

KNeeLifterEndPointAdj.jpg

I checked that as well and it is good. I can recreate the issue if I push down on the lift bar at the back that is connected to the lever underneath where the knee lift operates. How far is the presser foot designed to be moved up? Wondering if I am lifting too far? As I go up it becomes tighter and tighter. I will post a video of where it's hanging. Possibe the bar is bent? Man, I hope not. 

Sewing Machines:

Consew 206RB-1

  • Members
Posted

 

Sewing Machines:

Consew 206RB-1

  • Moderator
Posted

If rotating the adjuster screw doesn't free the presser bar, open the faceplate cover and observe the bar as you raise and attempt to lower it. You'll probably see where it is hanging up and be able to adjust or oil that part to free it.

Posted IMHO, by Wiz

My current crop of sewing machines:

Cowboy CB4500, Singer 107w3, Singer 139w109, Singer 168G101, Singer 29k71, Singer 31-15, Singer 111w103, Singer 211G156, Adler 30-7 on power stand, Techsew 2700, Fortuna power skiver and a Pfaff 4 thread 2 needle serger.

  • Members
Posted
2 minutes ago, Wizcrafts said:

If rotating the adjuster screw doesn't free the presser bar, open the faceplate cover and observe the bar as you raise and attempt to lower it. You'll probably see where it is hanging up and be able to adjust or oil that part to free it.

If I tighten the presser bar spring (flat) all the way down, it does come free, but then I have will have terrible marks in my leather. I have the front faceplate off and cannot tell where it is getting hung up. I definitely feel some rubbing as I get to the top.

Sewing Machines:

Consew 206RB-1

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

×
×
  • Create New...