Members DanishMan Posted February 14, 2020 Members Report Posted February 14, 2020 I finally managed to take apart the knife shaft Quote
Members Scoutmom103 Posted February 14, 2020 Members Report Posted February 14, 2020 Nice. That's a big change from how it looked. What type of paint did you use? Will you be sharing pictures of how it goes back together as well? Quote
Members DanishMan Posted February 14, 2020 Author Members Report Posted February 14, 2020 Hi Scoutmom For the inside, I used a normal metal paint. For the outside, I used Hammorite primer and a danish hammorite paint. It looks really good. Kind regards Søren Quote
Members jimi Posted February 14, 2020 Members Report Posted February 14, 2020 Oh! that looks nice Soren... I like that orange inside.... Quote
Members DanishMan Posted May 11, 2020 Author Members Report Posted May 11, 2020 I have been working on various PFAFF machines, so I have not had time for the skiving machine. However, I as am waiting for parts for my PFAFF 335 restoration, I have time to work on the Dania skiving machine. I am planning to fit two motors in order to give it independent feed. Also, I heard of someone, who had modified a vacuum cleaner to make it fit to a skiving machine. Anyone heard of this? Kind regards Soren Quote
Members Scoutmom103 Posted May 11, 2020 Members Report Posted May 11, 2020 Would you be so kind to put up pics as you put the skiver back together? And any mods you make like the two motors and a vacuum extractor. Quote
Members DanishMan Posted May 13, 2020 Author Members Report Posted May 13, 2020 Hi Scoutmon I will do that. Kind regards Søren Quote
Members DanishMan Posted May 14, 2020 Author Members Report Posted May 14, 2020 (edited) Starting to put the machine back together. I took apart in August, so it takes a bit of time to figure out, where the different screws go. Edited May 14, 2020 by DanishMan Quote
Members DanishMan Posted May 14, 2020 Author Members Report Posted May 14, 2020 (edited) Edited May 14, 2020 by DanishMan Quote
Members Scoutmom103 Posted May 14, 2020 Members Report Posted May 14, 2020 Hi DanishMan, Thank you for posting the pics of it going back together. Quote
Members jimi Posted May 15, 2020 Members Report Posted May 15, 2020 Ohhhh...Looking good Soren... Quote
Members bryan4christ Posted May 16, 2020 Members Report Posted May 16, 2020 beautiful !!! Does it run as good as it looks? Quote
Members DanishMan Posted May 16, 2020 Author Members Report Posted May 16, 2020 Hi Bryan Not yet - a few steps forward and then a few steps back. But I will get there. Cheers Quote
Members DanishMan Posted May 16, 2020 Author Members Report Posted May 16, 2020 99% done now. I only need to find a bakelite knob and a spring. And then to prepare the table and motors Quote
Members Scoutmom103 Posted May 16, 2020 Members Report Posted May 16, 2020 looking very nice. Did you have a engineers manual for this, or trial and error? Quote
Members DanishMan Posted May 17, 2020 Author Members Report Posted May 17, 2020 Hi Scoutmon This is my fourth skiving machine, so I am getting to know the basics. I have three more to restore. Kind regards Søren Quote
Members sainte Posted June 27, 2020 Members Report Posted June 27, 2020 Hello DanishMan, I had not seen your post !. Congratulations! It's a great job. Brds Quote
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.