Jump to content
Frodo

CHALLENGE !!!!!!!!!!!!!!!!!!!!

Recommended Posts

Looking good.   It's always a lovely thing when you get a commission - just to know that folks are willing to pay for work that you love to do!

- Bill

Share this post


Link to post
Share on other sites

dang nice job there, ima gonna have to build mine after huntin season.

Share this post


Link to post
Share on other sites

OK, everyone's experience will be different, but I've made dozens of beeswax-lined tankards, mugs, tumblers, cups, etc.... over the past several years and never had an issue with the beeswax degrading due to the alcohol content of the liquid.

I've used them for booze on the rocks, neat booze, booze cocktails, beer, milk, iced-tea, and even wine. In my un-scientific experience, full-proof liquor is not a problem for pure beeswax. I still use a 6-year old mug quite regularly. Damage and ruin to the beeswax has only ever happened because of physical trauma, like dropping. 

Although I've never used it, I've always assumed that brewer's pitch was better than beeswax in terms of the physical strength properties (resistant to dropping). I would never have assumed that something called brewer's pitch would be less able to withstand alcohol than good-old beeswax. Is this really true? 

Very hot liquid is another matter, I once did an experiment with hot coffee in one of my beeswax cups and it was not pretty. Although my test was not scientific in any way, I did confirm my theory that 'hot' liquid can ruin the beeswax (duh). 

Be aware that some of the 'food-safe' epoxies might not be recommended for constant contact with a liquid as would be needed in a cup or canteen. For example, I experimented with a product called Envirotex Lite, which the vendor says is safe for food 'contact' (i.e. cutting board) but not for immersion (i.e. cup or bowl). I made a few shot-glasses and a tumbler with it just to get the experience of using an epoxy, but compared to beeswax it was very difficult to work with and if it were my only option I would have given up on making drinking vessels due to how hard it was to get a good finished product. 

As soon as I get my workshop back in order I'll try making a canteen/bottle. 

Share this post


Link to post
Share on other sites

I use a triple hydrometer  in another hobby of mine  and found out rather quickly that an acrylic hydrometer will fall apart in front of your eyes and a glass one will not 

Share this post


Link to post
Share on other sites
10 hours ago, maxdaddy said:

Although I've never used it, I've always assumed that brewer's pitch was better than beeswax in terms of the physical strength properties (resistant to dropping). I would never have assumed that something called brewer's pitch would be less able to withstand alcohol than good-old beeswax. Is this really true? 

When I spend $150 for scotch, I do NOT want it to taste like pine.

Share this post


Link to post
Share on other sites
11 hours ago, maxdaddy said:

OK, everyone's experience will be different, but I've made dozens of beeswax-lined tankards, mugs, tumblers, cups, etc.... over the past several years and never had an issue with the beeswax degrading due to the alcohol content of the liquid.

I've used them for booze on the rocks, neat booze, booze cocktails, beer, milk, iced-tea, and even wine. In my un-scientific experience, full-proof liquor is not a problem for pure beeswax. I still use a 6-year old mug quite regularly. Damage and ruin to the beeswax has only ever happened because of physical trauma, like dropping. 

Although I've never used it, I've always assumed that brewer's pitch was better than beeswax in terms of the physical strength properties (resistant to dropping). I would never have assumed that something called brewer's pitch would be less able to withstand alcohol than good-old beeswax. Is this really true? 

Very hot liquid is another matter, I once did an experiment with hot coffee in one of my beeswax cups and it was not pretty. Although my test was not scientific in any way, I did confirm my theory that 'hot' liquid can ruin the beeswax (duh). 

Be aware that some of the 'food-safe' epoxies might not be recommended for constant contact with a liquid as would be needed in a cup or canteen. For example, I experimented with a product called Envirotex Lite, which the vendor says is safe for food 'contact' (i.e. cutting board) but not for immersion (i.e. cup or bowl). I made a few shot-glasses and a tumbler with it just to get the experience of using an epoxy, but compared to beeswax it was very difficult to work with and if it were my only option I would have given up on making drinking vessels due to how hard it was to get a good finished product. 

As soon as I get my workshop back in order I'll try making a canteen/bottle. 

i think i will go with beeswax as i trust your knowledge and experience, i have absolutely none on this. but my hard Spirits will stay in glass with maybe a leather cover lol.  i have plenty of homemade chokecherry wine for this project lol. So how do you get the beeswax inside evenly and the remainder back out ? Heating the leather as well as the wax? If so on the leather how hot?

Share this post


Link to post
Share on other sites

@chuck123wapati, I haven't made a canteen, yet, but have made several mugs with just beeswax and what I do is I put the mug in a food saver bag with beeswax and then seal it. In a pot that can accommodate it, I use a silicone oven mitt and start submerging the mug in the very hot but not boiling water until all the beeswax has liquefied and has coated the mug. Once you are sure all the leather is impregnated with beeswax, take it out of the pot and out of the bag. Ensure the shape is what you want it to be and then let it cool. Keep the beeswax in the bag and submerge it to keep it liquid and once the mug is cool enough, pour the beeswax back into the mug and slowly tilt it to cover the inside of the mug with the desired thickness of wax and pour out the rest. After the first one you figure out a lot on how to do it better on subsequent ones.

I say all that to say when I get to making the canteen, I'll approach it similarly. Not sure how to keep the belly on the canteen though, maybe just pour in the liquid wax from the start? YouTube probably has some answers too.

Share this post


Link to post
Share on other sites
43 minutes ago, battlemunky said:

@chuck123wapati, I haven't made a canteen, yet, but have made several mugs with just beeswax and what I do is I put the mug in a food saver bag with beeswax and then seal it. In a pot that can accommodate it, I use a silicone oven mitt and start submerging the mug in the very hot but not boiling water until all the beeswax has liquefied and has coated the mug. Once you are sure all the leather is impregnated with beeswax, take it out of the pot and out of the bag. Ensure the shape is what you want it to be and then let it cool. Keep the beeswax in the bag and submerge it to keep it liquid and once the mug is cool enough, pour the beeswax back into the mug and slowly tilt it to cover the inside of the mug with the desired thickness of wax and pour out the rest. After the first one you figure out a lot on how to do it better on subsequent ones.

I say all that to say when I get to making the canteen, I'll approach it similarly. Not sure how to keep the belly on the canteen though, maybe just pour in the liquid wax from the start? YouTube probably has some answers too.

thank you!  maybe a two step process impregnate the two pieces separately form them then sew them together then seal the inside. Wonder how that would effect sewing them up besides making any gluing impossible.

Share this post


Link to post
Share on other sites
On 10/8/2021 at 2:44 PM, chuck123wapati said:

thank you!  maybe a two step process impregnate the two pieces separately form them then sew them together then seal the inside. Wonder how that would effect sewing them up besides making any gluing impossible.

Yeah, gluing would be off the table but you could also just run a hairdryaer or heat gun around the stitch line and bond the beeswax from both side into one. That'll make it water (or whiskey) tight. Since you can't see the inside you could even forego the building up of the wax layer on the inside. It is more for aesthetics anyway.

Share this post


Link to post
Share on other sites

Busy busy busy

the order has grown from 10 to 20..

FYI,  you can make 10 bags out of 1- 10' D shoulder  

617.JPG.05ba20890361940db98b7cdb08ec63ed.JPG

Share this post


Link to post
Share on other sites
On 10/8/2021 at 11:06 AM, chuck123wapati said:

So how do you get the beeswax inside evenly and the remainder back out ?

Chuck, the waxing technique that I've settled on is:

  • Melt the wax in a double boiler setup
  • Pour some liquid wax into the mug filling it up about halfway
  • Tilting the cup slightly I SLOWLY rotate the mug around, letting the wax level slowly creep up the sides toward the opening.
  • While rotating the mug, keep it angled over the pot that the beeswax was melted in.
  • As I'm rotating the angled cup around I keep increasing the tipping of the cup so that eventually the wax is up around the opening.
  • As the wax is depositing itself at the opening of the cup I begin to let it pour back out into the pot while continually rotating.
  • Repeat as needed until the desired thickness is achieved 

The mug shown here probably had three sets of these steps performed about five minutes apart. I like to have a nice thick coating of the wax and each successive operation binds new wax to the the existing wax adding thickness. That's 10 oz skirting leather.

IMG_7327.jpeg.6391bf87cd24047674bb59ac206b6357.thumb.jpeg.657c93eebd7ce10a46a3624164bb3d0d.jpeg

 

5 hours ago, Frodo said:

the order has grown from 10 to 20

That's awesome! 

Edited by maxdaddy

Share this post


Link to post
Share on other sites
10 hours ago, maxdaddy said:

Chuck, the waxing technique that I've settled on is:

  • Melt the wax in a double boiler setup
  • Pour some liquid wax into the mug filling it up about halfway
  • Tilting the cup slightly I SLOWLY rotate the mug around, letting the wax level slowly creep up the sides toward the opening.
  • While rotating the mug, keep it angled over the pot that the beeswax was melted in.
  • As I'm rotating the angled cup around I keep increasing the tipping of the cup so that eventually the wax is up around the opening.
  • As the wax is depositing itself at the opening of the cup I begin to let it pour back out into the pot while continually rotating.
  • Repeat as needed until the desired thickness is achieved 

The mug shown here probably had three sets of these steps performed about five minutes apart. I like to have a nice thick coating of the wax and each successive operation binds new wax to the the existing wax adding thickness. That's 10 oz skirting leather.

IMG_7327.jpeg.6391bf87cd24047674bb59ac206b6357.thumb.jpeg.657c93eebd7ce10a46a3624164bb3d0d.jpeg

 

That's awesome! 

Man, don't you just love the smell of beeswax?   YUMMY

Share this post


Link to post
Share on other sites

before you say anything.:rolleyes:  Cause I know you guys do not MISS anything.  I am well aware that I did not stamp the edge of the dragon scales

this is where it will be formed and the edge will not be seen...Thats my story and I am sticking to it. 

 

002.thumb.JPG.4e5c6fc976b7d138ec403a94fc3f53ef.JPG

Share this post


Link to post
Share on other sites

I do believe you are really enjoying all this creativity. I hope you get a decent price for these bottles.

Now, I can see where the dragon scales are not tidy or are mis-aligned. But, you know what? I think it is all the better for that

(I must get a dragon scale stamp some time)

However. in this photo I did notice that you had a couple of gaps in your stitching holes lines - in the stack on the right. I hope you've noticed it yourself. Those gaps just might affect the sealing

18 hours ago, Frodo said:

617.JPG.05ba20890361940db98b7cdb08ec63ed.JPG

 

edited to add;

PS; what thickness of leather are you using and what are you packing into the bottle to make it shape?

 

 

Edited by fredk

Share this post


Link to post
Share on other sites

9oz leather,  i am packing corn, it falls out when you are done.

yes, i have a gap or 2.  those pieces  are not finished going through the line.   i catch the bs on the next step.  every hole gets an awl stuck in it

then it will be glued,  then sanded and edged   then sewn whew...  i gotta get busy !!!

Share this post


Link to post
Share on other sites

Thanks friend.

I'm rather caught up catching up with some resin casting at the mo, but I'll get on this asap

Share this post


Link to post
Share on other sites

 

this is still wet and full of corn.   

 

003.JPG.f010b105d4e8aeafa6f6a3e2bce71871.JPG

 

 

Edited by Frodo

Share this post


Link to post
Share on other sites

Several months later. . . . 

Neddy Seagoon* returns to the fray . . . . . 

Bluebottle* has come up with an idea . . . .  whack!  . . . . . . . . . .. . thats the end of that and Bluebottle* is now deaded

However, I've not forgotten this. It was put on the 'back burner' as a saying here goes.  I had it written down on a bit of paper (Bluebottle & Eccles)*

This morning I ordered 2kg, about 5 pounds, of pop-corn kernels. Some might be used in making a bottle/flask and some might be made into grits and some made into popped corn

It might not take 3 months for me to get to the next stage. 

On the other hand. . . . . .

 

 

is a glove

 

* I'll let you google up those names

 

Share this post


Link to post
Share on other sites

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.


×
×
  • Create New...