Members Jazznow Posted November 29, 2023 Members Report Posted November 29, 2023 (edited) Hi everybody. My boss gave me the task to dial in the old fortuna bell skiver that wasn't in use for 10 years. Settings were all over the place but I got to the point where it will skive the leather that we will use. Only thing left is the ridge/edge at the end of the skive. I would like to have that a bit less. A more feathered skive. Anyone can point me in the right directions? Edited November 29, 2023 by Northmount fixed title typo Quote
RockyAussie Posted November 29, 2023 Report Posted November 29, 2023 The knife may need to come forward a little but see what happens when you reduce the feed stone pressure about1/2 turn first. The adjuster right at the rear back. Quote
Members Jazznow Posted November 29, 2023 Author Members Report Posted November 29, 2023 Do you mean the one sticking out at the back (to the left in the picture)? That one is so tight I can't even turn it with help of pliers. On the side there are two knobs. The right one moves the feed stone up an down and the left one I have no idea what it does, can't see any change when turning that. Quote
Members Jazznow Posted November 29, 2023 Author Members Report Posted November 29, 2023 Thanks again. I was able to get better results now. Still not perfect but ok. Quote
Members keithski122 Posted December 4, 2023 Members Report Posted December 4, 2023 (edited) Check out nippy_kikai on instagram, they make skiving machines and have some helpful videos on using and setting up. Edited December 4, 2023 by keithski122 Quote
Members xnikolaos Posted December 7, 2023 Members Report Posted December 7, 2023 Jazznow, look at the pdf file I'm sending you. It is two pages of Italian FAV1,2 manual. It is the same machine as the FORTUNA with minor modifications. If you learn these pages, then you will understand how the old FORTUNA type skiver works. AV1 AV2.pdfFetching info... Quote
Members TomE Posted December 7, 2023 Members Report Posted December 7, 2023 On 12/7/2023 at 11:18 PM, xnikolaos said: Jazznow, look at the pdf file I'm sending you. It is two pages of Italian FAV1,2 manual. It is the same machine as the FORTUNA with minor modifications. If you learn these pages, then you will understand how the old FORTUNA type skiver works. AV1 AV2.pdf 53.09 kB · 1 download Expand This is very helpful. Thank you. First I've seen it recommended to angle the feed roller for a tapered skive. Also, varying the distance between the foot and the bell according to the thickness of the leather. Any chance you could provide the complete manual? I have ordered a couple of FAV roller feet from Campbell-Randall that use the eccentric pin mentioned here. Would like to read how FAV recommends using this adjustment. Quote
Members xnikolaos Posted December 7, 2023 Members Report Posted December 7, 2023 On 12/7/2023 at 11:34 PM, TomE said: This is very helpful. Thank you. First I've seen it recommended to angle the feed roller for a tapered skive. Also, varying the distance between the foot and the bell according to the thickness of the leather. Any chance you could provide the complete manual? I have ordered a couple of FAV roller feet from Campbell-Randall that use the eccentric pin mentioned here. Would like to read how FAV recommends using this adjustment. Expand Yes I can send them to you but the file is larger than 1.5Mb. I think email is easier. Quote
Members TomE Posted December 7, 2023 Members Report Posted December 7, 2023 On 12/7/2023 at 11:47 PM, xnikolaos said: Yes I can send them to you but the file is larger than 1.5Mb. I think email is easier. Expand Will message you with my email address. Thanks so much. Quote
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.