Jump to content

Recommended Posts

I have no idea where else to ask this, but I have found more information about the singer 42-5 here, than anywhere else. I am starting a saddle and blanket repair business, and have the opportunity to buy a singer 42-5. After reading other forums, I think i will do quite well for the blanket repair, but I have no idea what it is worth. All the parts are there, and it was in good working condition 1.5 years ago before it's owner passed away. The owner used it for blankets, saddle pads, and canvas work on a regular basis. It has been in storage since. I know that without actually looking at it, no one can give an exact value, but a ballpark range would be great. Thank you in advance for any help you can offer!

Share this post


Link to post
Share on other sites

I'd say $3-400.00,it's a great machne for this type of work,but the problem is we can't get all the parts for it anymore.So try it before you buy itto mak sre t's ing good if ntit wll make it worth less of courseif you hae to bu parts.

Share this post


Link to post
Share on other sites

I have one of them, and I use it for nearly everything, up to leather 1/4" thick. Great for canvas or upholstery fabrics too. Bobbins are available. Use commonly available series 135x16 and 135x17 needles. I mostly use 69 and 138 thread in mine, because I have plenty on hand. I'm not sure if it would handle heavier thread or not, because I never tried it. For the seriously heavy stuff, I have my big Cowboy machine.

As Cowboy Bob says, it's great if you don't need parts. In my experience, worn or damaged parts can be repaired, screws re-made, etc. I have fixed a lot of old parts made of "Unobtanium", because I have machining and welding capabilities. The real problem would be if something is missing, rather than worn or broken.

Share this post


Link to post
Share on other sites

One of my customers needed a machine for 8mm of harness leather with 277 thread and the only machine I had was a 42-5. Tested it out as a treadle and it worked like a dream.

Needle plate and feed dogs are no longer available but this may be fixed soon ;)

This is the king of flatbeds.

Share this post


Link to post
Share on other sites

Anyone know where I can Gert a needle plate for the 42-5 ?  I have the main one, but the one where the shuttle lives is missing

Share this post


Link to post
Share on other sites
1 hour ago, usmc323 said:

Anyone know where I can Gert a needle plate for the 42-5 ?  I have the main one, but the one where the shuttle lives is missing

I too have a 42-5 and aside from needles and bobbins, replacement parts are made of Unobtanium. That is unless you can find somebody selling one cheap or for scrap.

Share this post


Link to post
Share on other sites

Haven´t yet seen a 42 in person but the machine looks like a beefed up Singer 16 so I would guess some sort of Singer 16 needle plate could fit but depends on what feed dog you have installed. Maybe worth checking with this seller and compare measures:

https://www.ebay.com/itm/303485230634

Just a guess!

Edited by Constabulary

Share this post


Link to post
Share on other sites

Might want to avoid that seller. They are not on the reasonable side.

Share this post


Link to post
Share on other sites

Folker, that throat plate for the Singer 16 does not look like the plate on my 45-2. It will not fit if the O.P's feed dog is like mine, with the second row of teeth on the right side. My throat plate measures 3 1/4 x 2 1/8 inches. I will post a photo of it later.

Share this post


Link to post
Share on other sites
On 1/2/2014 at 8:37 AM, Cascabel said:

I have one of them, and I use it for nearly everything, up to leather 1/4" thick. Great for canvas or upholstery fabrics too. Bobbins are available. Use commonly available series 135x16 and 135x17 needles. I mostly use 69 and 138 thread in mine, because I have plenty on hand. I'm not sure if it would handle heavier thread or not, because I never tried it. For the seriously heavy stuff, I have my big Cowboy machine.

As Cowboy Bob says, it's great if you don't need parts. In my experience, worn or damaged parts can be repaired, screws re-made, etc. I have fixed a lot of old parts made of "Unobtanium", because I have machining and welding capabilities. The real problem would be if something is missing, rather than worn or broken.

The presser foot for my Singer 42-5 broke (at the needle hole) I need a replacement, or a good way to fix it.  Any ideas where I could get a replacement or have it fixed.  The  Singer part number 5816.

42-5 Presser foot .jpg

Share this post


Link to post
Share on other sites
8 hours ago, sdgengineer said:

The presser foot for my Singer 42-5 broke (at the needle hole) I need a replacement, or a good way to fix it.  Any ideas where I could get a replacement or have it fixed.  The  Singer part number 5816.

I'd see if I could find someone local who could do a hard soldering job.

So either silver solder or bronze solder. 
Silver soldering can be done using a Mapp torch, and it is incredibly tough and it works on most materials. 

Someone installing air conditioning plants or refrigeration machinery tend to use silver soldering a lot, so if you have some local company that does that it might be worth giving them a call.

Good luck with the repair job.

Brgds Jonas

Share this post


Link to post
Share on other sites

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.


×
×
  • Create New...