Jump to content

Recommended Posts

  • Members
Posted

If someone can help by providing information or pointing me in the right direction I would be most appreciative. I have been searching the forum trying to figure out how to "polish" pricking irons. Some of the irons I have from Osborne and Joseph Dixon are a bit rough, and I would like to know an efficient way to get in between all of the teeth. The metal is pretty hard on some, I believe the Osborne irons are drop forged. I have tried wrapping sandpaper around a flat bit of leather, but I am concerned I will actually wear a different angle into the teeth, ie sand only one side. This is less of an issue on the European style irons than on the diamond shaped stitching chisels, which are designed to go completely through the leather. Many of these are really rough the entire length of the tooth, which makes them difficult to pull out of the leather once punched through.

Thanks in advance for any advice!

post-57438-0-65567800-1429633592_thumb.j

For other images:

http://leatherworker.net/forum/index.php?app=galleryℑ=28911

YinTx

  • Members
Posted

im interested as well.This subject is something that would be taught in european leather school, information is hard to come by. The easiest way I would think would be to apply green rouge on a piece of thin cardboard material. Just polishing the teeth would make them slide out easier while removing the minimal amount of iron.

If you are hitting the iron all the way through till the leather reaches the full distance of the teeth it will likely always stick to the leather.

You can use the same tools the toolmaker uses to sand the iron teeth down (rasp used for metal). Do know that this requires a expert touch so damaging your tool is a possibility. If you do decide to sand the teeth i would be interested in pictures.

  • Members
Posted

Hi yin, you might want to try emailing Nigel Armitage about this, i know on some of his review videos he mentions polishing his pricking irons, he has always helped me out in the past.

  • Members
Posted

If someone can help by providing information or pointing me in the right direction I would be most appreciative. I have been searching the forum trying to figure out how to "polish" pricking irons. Some of the irons I have from Osborne and Joseph Dixon are a bit rough, and I would like to know an efficient way to get in between all of the teeth. The metal is pretty hard on some, I believe the Osborne irons are drop forged. I have tried wrapping sandpaper around a flat bit of leather, but I am concerned I will actually wear a different angle into the teeth, ie sand only one side. This is less of an issue on the European style irons than on the diamond shaped stitching chisels, which are designed to go completely through the leather. Many of these are really rough the entire length of the tooth, which makes them difficult to pull out of the leather once punched through.

Thanks in advance for any advice!

attachicon.gifDixonIrons.jpg

For other images:

http://leatherworker.net/forum/index.php?app=galleryℑ=28911

YinTx

What's wrong with that iron? Even Blanchards have machining marks on them.

I narrowed the tines on an Osborne by lapping the sides on a piece of emery paper on glass so I can definitely say that at least modern Osbornes are not too hard to work with.

You can sharpen them with progressively finer grit steel nail files. Cheaper than a set of jewelers files.

  • Members
Posted

Nuttish,

These are brand new, so I am hoping that there is absolutely nothing wrong with my irons! Only issue is that they are a bit rough in the teeth, and some of the teeth are a bit fatter than others, and some have rather large burrs on them keeping them from making a clean mark. I only want to clean them up a bit, but I have been unsure how to go about doing this without causing damage to the teeth. Was struggling with how to get in between the teeth cleanly without hitting the nearby teeth while working. Hadn't thought of jewelers files... and are your referring to using fingernail files? Sounds like something that would work well! Thanks for the tips.

Sandpaper on thin wood sounds like it would work well too, especially when I get into finer grits. Thanks for that idea, RStevenson.

I will PM Mr. Armitage on this topic, to see if he responds. I did make a post on his video reviews regarding irons, but he hasn't responded. Hopefully I haven't insulted him in some way!

YinTx

  • Members
Posted

Soak a piece of wet/dry abrasive paper and lay it on your granite block for the large flat sides. I start with 500 grit and progress to 1000 then lap on an Arkansas stone or go straight to white rouge on a thin leather strop flat on my bench. Between the teeth you can wrap a piece of plastic or a wooden tongue depressor with soaked wet/dry paper and (painstakingly) polish between each tooth. Clamping the iron in a small vice helps to reduce rounding the edges and maintaining the teeth angle Follow up with a rouge loaded strip of leather.

Stroke in one direction (l/r or up/down only, you choose) after you've removed any major imperfections to reduce the amount of polishing you have to do if you want a mirror-like finish.

  • Members
Posted

I wouldn't use sandpaper on thin wood. The paper will invariably bulge and cause you to round over corners. I take it from your extreme perfectionism that you wouldn't want that.

Yes, I'm talking about fingernail files. They're tremendously useful tools for all kinds of things.

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

×
×
  • Create New...