Jump to content

Recommended Posts

  • Members
Posted

Hi. Is there a tip or tools to help place zippers evenly and accurately in hand bags? When applied as closures at the top of the bag? Any advice is greatly appreciated!

  • Members
Posted

This MLP4 model in the link is what I have used before in heavy marine canvas zippers prior to stitching.  I found it to be great, though expensive and I guess a reason the T-pins are my go to tool. With either method the removal at time of or after the stitching. Respectfully as mentioned I used and someday would like to have one. The clear double sided seam or even basting tape could be used for sure. The t pins are handy and several lengths the 2” is good for my canvas stuff but take a look at JoAnns possibly.

Good day

Floyd

 

http://www.markwellusa.com/product_p/mpl4m.htm

  • Members
Posted

Thanks for all the replies! But I'm not talking about placing as far as adhesives/tape... I mean making sure the material is lined up evenly on the zipper. So if it's between two pieces of leather...is there a guide or tool to help glue/ tape both pieces in the same place so when you sew.. the stitching is the same distance from the edge on both sides. I hope this makes sense!

  • Members
Posted

Ok that sounds like what I need. I am going to try making my own contraption with either a strip of leather or bag stiffener. Thanks! I will see if I can find what you are talking about.

Posted
On 03/02/2018 at 1:25 PM, JeannieH said:

Thanks for all the replies! But I'm not talking about placing as far as adhesives/tape... I mean making sure the material is lined up evenly on the zipper. So if it's between two pieces of leather...is there a guide or tool to help glue/ tape both pieces in the same place so when you sew.. the stitching is the same distance from the edge on both sides. I hope this makes sense!

I hate zipper installation:censored2: and I wish there was a magic tool to do what you say but as yet I haven't heard of it. AS a rule I make the under side a little closer to the middle of the zip as it is easy to end up too close to the edge when you are stitching and cant see it. Here in some pictures following I show some jigs that I use for making up the bag in the first picture.

DSC01553_resize.JPG

This next pic shows a drawing printed out with some bits of firm veg stuck to it. The aim is to get the lining and all of the following bit including the zip in exactly the right location.

DSC01554_resize.JPG

I didn't have handy a fully prepared lining but I think you will get the idea alright.

DSC01555_resize.JPG

After all of the padding and croc etc is glued down and in place the zipper is glued on the top side and attached to the centre stip shown below in cardboard. This then gets glued into place over the lining.

DSC01558_resize.JPG

In order to glue up the zip I make up a stick with a groove and hollow in it for the slide and with the clamps holding it in place I am able to neatly glue up the zip. The stick below is not the right length for the zip shown but again I think the idea is clear enough.

DSC01550_resize.JPG

DSC01549_resize.JPG

This pic below is a prototype and not stitched correctly but may help to understand the process somewhat.

DSC01556_resize.JPG

A tool like i have made below or a variation of can sometimes be of use when locating a zip into place.

DSC01560_resize.JPG

I hope that is of some help and I wish for you patience and luck. Brian

 

 

WH.jpgWild Harry - Australian made leather goods
YouTube Channel
Instagram

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

×
×
  • Create New...