Jump to content

Buying oblong punch tool (new or used) 25x6mm


Recommended Posts

  • Members
Posted

@480volt: Outstanding, but it's really ruining the structure of the forum. Maybe should resize it to smaller? It would fit way better into the posts :)

  • Replies 21
  • Created
  • Last Reply

Top Posters In This Topic

Posted
2 hours ago, Mocivnik said:

@480volt: Outstanding, but it's really ruining the structure of the forum. Maybe should resize it to smaller? It would fit way better into the posts :)

Huh?

In my browser, it shows up as the typical upper left hand corner icon, not in the body of the post. What do you see?

  • Contributing Member
Posted (edited)

I get a picture of a roll of steel cable. The picture is approx 4 to 5 times the size of your actual message block in the above post. I use a lap top with a 15 inch screen. The height of the screen is 7.5 inches and the picture is larger than this [using my Firefox browser at 100%]

Edited by fredk

Al speling misteaks aer all mi own werk..

  • Contributing Member
Posted
8 hours ago, Mocivnik said:

@480volt: Thanks for all the info, but I've contacted in a supplier in the EU as @fredk adviced.

ps: What's with that banner of a steel wick in your signature?

Go to 480volt's signature; on the far right, at the top is a little x. Click on that and it will give you an option to ignore his signature. It makes the picture go away

8 hours ago, Mocivnik said:

PS: Since I live in Europe, we have metric system and leather belts made here are standard dimensions 40mm (1.575"), but end strap punches are availible only in sizes such as 1.5" and 1.75".
Does 1.75" suits better for this kinda work?

Yes. I use the 1.75 size for all my belts and straps except for the very littlest ones eg 16mm and below. It just needs careful alignment to get the V even on both sides

Al speling misteaks aer all mi own werk..

Posted

Interesting. I’ll have to log in with a different browser and see what there is to see. With safari on an I-phone, all is well.

  • Members
Posted
On 2/19/2018 at 5:18 AM, fredk said:

Check out LePrevo in England

Slot Punch T129

http://www.leprevo.co.uk/hole-punches.htm

http://www.leprevo.co.uk/photos/slot-punch.html

I use them and they are good

They also do the belt end punches

T130

http://www.leprevo.co.uk/knives.htm

I've contacted them and order tools, thanks!

 

How would you compare their quality versus Osborne or Craftool?

  • Contributing Member
Posted

I don't own any Osborne but I think their tools are better than most Craftool

Al speling misteaks aer all mi own werk..

  • Members
Posted

Oh, I thought same.

They are super friendly and polite, they take order kinda personally. I really like them.

Posted
On ‎20‎/‎02‎/‎2018 at 7:49 AM, fredk said:

Go to 480volt's signature; on the far right, at the top is a little x. Click on that and it will give you an option to ignore his signature. It makes the picture go away

I don't see any little x in that location.

Kindest regards

Brian

 

"Whether you think you can or whether you think you can't, you are right"  Henry Ford

Machines: Singer 201p, Kennedy,  Singer 31K20, Singer 66K16 ("boat anchor" condition), Protex TY8B Cylinder Arm (Consew 227r copy), Unbranded Walking Foot (Sailrite LSV-1 copy)

Posted

It's faint, next to the top right of the big picture. If you tap it you can deselect one signature or all signatures,

H

No longer following it.

 

Guest
This topic is now closed to further replies.

×
×
  • Create New...