Techsew shopping cart checkout

[Thescandall]

I need bobbins for my 5100 , but it says some addresses kinda stuff and won’t let me finish the order. I live in Texas but I don’t see where that could be a problem. Using PayPal might be it. I don’t know. Any other folks have issues.  Regular 441 type won’t work because the hole is not correct.  Even tried Juki, Hightec and others.  I have 1 left.      NEED Bobbins. 

[Northmount]

@Techsew Ron  Looks like a dude here needs your help.

 

[Thescandall]

Well I guess it’s just the signal when I’m at the ranch. Tried from town this morning and the bobbin order went thru.  

[Arturomex]

Glad to know you've been successful.

I'm not understanding the problem you've had with other bobbins. Are they not interchangeable between the 441 class machines? What seems to be the difference?

Regards,

Arturo

[Thescandall]

14 minutes ago, Arturomex said:

Glad to know you've been successful.

I'm not understanding the problem you've had with other bobbins. Are they not interchangeable between the 441 class machines? What seems to be the difference?

Regards,

Arturo

The hole in the Juki bobbin will not line up with the winding  pin on the techsew machine. Same with the high lead and others. 
I’m sure they could be drilled a little closer to the center post of the bobbin but I would like to have the correct ones. 

[MtlBiker]

20 minutes ago, Thescandall said:

The hole in the Juki bobbin will not line up with the winding  pin on the techsew machine. Same with the high lead and others. 
I’m sure they could be drilled a little closer to the center post of the bobbin but I would like to have the correct ones. 

That's really interesting...  From what you report it sounds as if the bobbin on the 5100 is different from that on the 2750 (which I have).  Do you know if that's really the case?  I would be surprised.

I buy generic "M" bobbins from Wawak and they work perfectly in my Techsew 2750 and also in my Consew RB206-5.

[Thescandall]

Unless the pin is supposed to go in the slot on the bobbin. I just got this machine yesterday. I tried the slot on the Juki bobbin and it didn’t work either. Slot was too narrow. 
 Go figure.  I’m new to this stuff. 
 

[MtlBiker]

8 minutes ago, Thescandall said:

Unless the pin is supposed to go in the slot on the bobbin. I just got this machine yesterday. I tried the slot on the Juki bobbin and it didn’t work either. Slot was too narrow. 
 Go figure.  I’m new to this stuff. 
 

I'm at my day job and don't have a bobbin with me.  I'm not quite sure what you are talking about regarding a slot on the bobbin.  I'll look at my bobbins tonight when I get home, but I've never given any thought at all to any kind of "slot" on my bobbins.

You're new to this stuff and just got the fabulous TechSew 5100?  Congratulations!  I hope you got the speed reducer and needle positioner with it.  I think it's like my 2750 PRO but uh, better.  What is your intended use for the machine?

 

[MtlBiker]

@Thescandall - are you talking about the little slot which is at about the 8 o'clock position on this photo?

That slot is not used at all when the bobbin is inserted in the bobbin case.  As a matter of fact, I don't think it's used at all, except maybe on the bobbin winder to keep the bobbin from just spinning freely.  But (I'll confirm it when I get home) I don't think even my bobbin winders use that slot.  The bobbin just fits on the split shaft on the winder and is held by friction.

 

[Thescandall]

My bobbins are huge.  Not like yours at all. I get about as much on my fishing reel   Lol

Edited January 13, 2022 by Thescandall