Patterns and Templates
Learn how to create your own, or how to use standard patterns.
1,677 topics in this forum
-
- 1 follower
- 3 replies
- 7.7k views
Copied from his YouTube post: Hi all! Finished a project that had dragged on for several months. 80% reversible design. Unfortunately, the pieces of leather for the edges were not long enough. I had to make 2 jumpers, which is not very beautiful. Pattern for a punch with a step of 5mm. The main frame is vegetable tanned leather 1.6 thick. The edging and the inner part of the straps are pueblo leather 0.8mm. - claim. suede with glue base. pattern. Uploaded PDF from his website: gray_backpack_AK.pdf
Last reply by BLURDWORX, -
-
-
- 3 followers
- 61 replies
- 29.8k views
Does anyone have or know where I could obtain a shoulder holster pattern for a uberti / ruger birdhead 45LC. I have seen many makers of this pattern but have not been able to find one online anywhere thus far. I have attached a pic of the style I am looking for. Anyone's help sure would be appreciated. thank you...
Last reply by insight, -
- 7 replies
- 2k views
Hi all! I recently bought a few patterns from here after some recommendations, and I am having some trouble getting them printed so I can use them. I went to office depot this morning as recommended by the seller and that was an absolute waste of time. After and hour and a half standing around I left with patterns that were worthless. All the information I got from the seller was "best printed on wide format printer" and that was verbatim what I told the woman at the desk and is all the information I can find on the website. Can anyone help me with this? Perhaps some recommended printer settings? I have not had much luck with getting in contact with the seller in t…
Last reply by maggielj, -
- 1 follower
- 0 replies
- 735 views
I hadn’t been able to find anyone selling acrylic templates in a 20/16mm taper so contacted Buzzard Brain Leather on Etsy and the owner Will was kind enough to design a one off for me in that taper and length of 105 and 65mm. Same cost as his ready made sizes too. They arrived within a week from Louisiana to Alberta and they are very well made, unlike some Ali Express ones I received in the past (20/18 and 18/16 regular length.There is enough overhang for the spring bar and buckle flaps that I’ll be able to cut 110 and 70mm lengths as well.
Last reply by CalgaryJim, -
- 2 replies
- 1.2k views
Does anyone have a pattern that will fit a gp100, With a 6” barrel?
Last reply by Adam2hunter, -
- 0 replies
- 673 views
When the articles about building the Stohlman workbenches was printed in 1969, there was also 4 pattern packs with the patterns for the Wood inlays for sale. Does anyone have these for sale, or the possibility to copy or scan them ? I would love to have these patterns for woodworking.
Last reply by oyvindbl, -
- 0 replies
- 793 views
This is about enjoyable as tooling
Last reply by Stewart, -
- 3 followers
- 5 replies
- 1.8k views
Does anyone have a good Marlin 336CS Lever Wrap pattern?
Last reply by MarlinDave, -
- 1 follower
- 2 replies
- 1.6k views
Ive seen the SLC pattern that is available, but i think id have to make a lot of adjustments to it. Which i may have to do with any pattern of course, but wondering if anyone has leads on where to download or purchase a more modern looking pattern for a set of rodeo chaps. Thanks
Last reply by TomE, -
- 1 reply
- 2.1k views
Hello all! I am trying to make a EDC belt type tool pouch. I need to put in it a leatherman, a med size flashlight, a pen. I have made a belt case for a leatherman but it turned out not so good. I was wondering if anyone had made one before or has a template/pattern better then what I messed with? something along the lines of this? Thank you Thank you !!
Last reply by Mablung,
