Jump to content

Recommended Posts

Posted

It's not too bad from ten feet but I don't care, I've learned so much. I like to challenge myself and this was a challenge . I even made the leather strap thing that goes around the cord and joined the pieces together with that diagonal/right angle thing. I didn't do myself any favours with a fairly tight curve and those corners were tough. Even though I skived everything it's difficult to find the piping under the second piece of leather and it's a constant worry that you want to get as close to the piping as you can but you don't want to break the needle. Not sure if I was using the right size piping foot and I'm not sure sure if a piping foot is even needed with tight corners because they just wanna go straight on. I don't know if I'm brave enough to attempt the smaller pocket that sits in the middle of this one. 

Piping.jpg

  • Members
Posted

Looks good to me toxo. I think you did fine. @toxo what machine did you sew your bag up with? 

Thanks.

Posted
10 hours ago, DieselTech said:

Looks good to me toxo. I think you did fine. @toxo what machine did you sew your bag up with? 

Thanks.

Thanks mate but I think you might be overdue a visit to the optician lol.

The machine choice was purely because of the presser feet. I have lots of em for the Durkopp 239 and the new machine but not so much for the Adler 69 and because it was "practice" the thread/colour didn't matter so much either so the turned edges were done on the 69 using the colour "Toast" and the piping foot was on the new machine using a blue thread which also tested the theory that, if done right you won't see the thread.

  • Members
Posted
40 minutes ago, NatesLeatherGds said:

Nice. 

Ok - million dollar question -- never done piping, I like the look - but... why piping ? Does it help structure? Look good? Opinions and facts welcome :)

Well, if you want opinions, I got 'em!  Seriously, I think the piping "hides" the stitching on a turned item.  It should also protect the thread from abrading if exposed.  JM2C, Jim

Posted (edited)
1 hour ago, NatesLeatherGds said:

Nice. 

Ok - million dollar question -- never done piping, I like the look - but... why piping ? Does it help structure? Look good? Opinions and facts welcome :)

This is a huge question. Firstly I'll repeat something I've often said,  there's not a lot of mystery to leathercraft, far more common sense and finding a way to fulfill a purpose. "Piping" covers a huge swathe of applications. Piping "cord" can be many things. I put the commas around the word because some piping uses no internal cord at all. Then there is the choice of the size of cord that's used according to the project. As an example I think the size I used here is bigger than I would like for that size of pocket. If doing it for real it would be smaller. What's the cord made of? This goes to some of your question @NatesLeatherGds, plastic cord could help hold up a bag made of thinner leather, some piping cord is made of soft cotton type material which might be useful along with a soft leather when you don't want chafing against someone's skin such as clothing or a nice collar maybe. Of course most piping is used as a decorative detail and can be very effective and not just on edges either. I'm getting excited about learning about double piping on bag panels. Check this out. Forgive the ads.

UPHOLSTERY TIPS - How you can make a double Piping - MECA - YouTube

Edited by toxo
Posted

I am no expert at doing piping either but for what it is worth I do the front or back panel first with the piping marked out glued on the stitched around the edge to hold it firm as shown in these pictures -

This one shows the piping glued to attach to the back piece

DSC02461_resize.JPG

The corners have to be clipped to allow the piping to go around the tight curve

DSC02466_resize.JPG

The join overlap I do as shown

DSC02468_resize.JPG

I then stitch around the outer edge

DSC02476_resize.JPG

I then attach with clips the panel to the gusset as shown -

DSC02481_resize.JPG

This video shows the next step sewing the pieces together

After that I run a binder tape around on the inside as shown in this video -

The finished bag which is only a prototype at this stage hence a bit ordinary.

DSC02498_resize.JPG

Hope that is of some help.

WH.jpgWild Harry - Australian made leather goods
YouTube Channel
Instagram

  • Members
Posted
1 hour ago, RockyAussie said:

I am no expert at doing piping either but for what it is worth I do the front or back panel first with the piping marked out glued on the stitched around the edge to hold it firm as shown in these pictures -

This one shows the piping glued to attach to the back piece

DSC02461_resize.JPG

The corners have to be clipped to allow the piping to go around the tight curve

DSC02466_resize.JPG

The join overlap I do as shown

DSC02468_resize.JPG

I then stitch around the outer edge

DSC02476_resize.JPG

I then attach with clips the panel to the gusset as shown -

DSC02481_resize.JPG

This video shows the next step sewing the pieces together

After that I run a binder tape around on the inside as shown in this video -

The finished bag which is only a prototype at this stage hence a bit ordinary.

DSC02498_resize.JPG

Hope that is of some help.

@RockyAussie what class of cowboy sewing machine was you using in them sewing videos? 

Also where did you get your binder tape attachment? 

Thanks. Great videos by the way. 

Posted
3 hours ago, DieselTech said:

@RockyAussie what class of cowboy sewing machine was you using in them sewing videos? 

Also where did you get your binder tape attachment?

There are 2 different machines in use on them. The one with the binding tape is an Elizabeth TK-335 which is basically a copy of the Pfaff 335. The machine came with the binding parts already on it and the tape folding part came from the dealer but they are pretty common to get over the net. The Cowboy one is a CB246 which is basically a copy of a Juki machine. I believe they don't stock them in the States but Techsew have a version which is 2600 if you want to check them out. This video I did awhile back shows some of the features I think are important -

 

WH.jpgWild Harry - Australian made leather goods
YouTube Channel
Instagram

Posted

I have been wanting to do piping, but I don't know where to find affordable setups for a cowboy 4500, I'm open for suggestions 

Doc Reaper

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

×
×
  • Create New...