Hand-cast solid Brass Buckles from a small foundry

[Origibelts]

Hi everyone,

I’m new here and just getting started with a small project I’ve been working on for some time: hand-cast solid brass buckles and hardware. I run a small foundry and workshop near Nairobi, Kenya, where I make each buckle in small batches using traditional sand casting.

Right now I’m at the stage of introducing these pieces and learning what makers actually look for in their hardware. Strength and authenticity are my focus, but I’d love to hear what you value most — sizing, finish, style, or price point.

Here’s a look at what I’ve made so far:
https://origibelts.com/collections/wholesale

Any thoughts or feedback would be really appreciated as I start this journey. Thanks for letting me be part of the community.

Sincerely,
John G.
Origibelts – Nairobi, Kenya

[Mulesaw]

Hi John G
Welcome to the forum.

To me the most important points are:

Strength/solidity
Size
Design/style

Finish to me is part of the style, and I normally prefer just a regular brass finish like the one in your picture, alternatively it could be silver coloured, but I prefer no "bling" on my buckles.

Price is not especially important since I don't make 1000 belts, and compared to the time invested in making a nice belt, the price for a buckle is only of secondary importance. But I guess that if you run a regular production of belts, it is of more importance.

I like the small "dip" where the prong of the buckle nests. That is a nice touch in my opinion.

Depending on what type of product I am making, I use either "normal buckles" like the one in your picture, or "roller buckles" or "center bar buckles"
For belts I prefer sizes 1.25" and 1.5" (30mm and 38-40mm).

Brgds 
Jonas

Edited 4 hours ago by Northmount
fixed typos

[DieselTech]

Looks nice! But here is your weak link!

[dikman]

I'm curious why that is the weak link? What am I missing? It doesn't look any different to me than other buckles I have.

[Origibelts]

@Mulesaw
 

Hi Jonas,

Thanks so much for the thoughtful feedback — that’s exactly the kind of perspective I was hoping to hear.

I’m glad you noticed the little “dip” for the prong; that was something I experimented with to make the buckle both more solid and a bit easier to use. I’ll definitely take your points on board: strength and solidity first, then style and sizing in the 1.25" and 1.5" range. Roller and center bar buckles are already on my sketch pad, so it’s encouraging to hear those are useful for your work as well.

And I hear you on finish — a straightforward brass look is also my preference, no plating or “bling.” It keeps the buckle honest, and it develops a patina that works well with leather over time.

Really appreciate you taking the time to share your view. It helps me make sure what I produce is actually useful to makers like you.

Best,
John

[Origibelts]

@DieselTech
 

Hi DieselTech,

Thanks for pointing that out. The prong and the joint where it nests in the frame is definitely the area I’ve focused most on reinforcing during casting and finishing. I’ve been testing different thicknesses and alloys to make sure that part stands up to stress, since I know that’s where buckles usually fail.

 

Best,
John

[Origibelts]

@dikman
 

Hi Dikman,

Good question — you’re not missing anything obvious. The prong/tongue area where it pivots is what tends to give out first on a lot of buckles. That’s what DieselTech was flagging. I’ve been beefing up that joint in my castings so it holds up better under stress.

Best,
John

[Dwight]

Just a curious question . . .  if someone was to send you a "pattern" . . .  made of plastic . . .  cut out on a computer based machine . . .  of an exact personal buckle . . .  would you be up to making that buckle?

I'm thinking of the American Western buckle type . . . 

May God bless,

Dwight