Members llasso Posted January 18, 2008 Members Report Posted January 18, 2008 Good Morning, Please find picture of the Roy Rogers Reproduction Gun Belt and Holster set I just finished. This rig took about 60 hours from start to finish. It is made from 8/9oz leather with 4/5oz leather lining. The belt is 3.5” wide and is set at 39” center it will go down to 37” and up to 41”. This rig is completely carved even under the billet straps and the holster flaps are also carved. I have attached a retention strap to this rig that is blind stitched. That means you do not see it from the front side of the belt. It also has two access entry points in the back of the belt that allow to change the buckle if you so desire.. These points allow the screws on the buckle to be sub- surface , so as not to mar the leather . There are hammer thongs on each holster. There are 36 bullet loops for 45 or 44 caliber bullets. The holsters are made for a Colt SAA 45, The toes of the holsters are open so any length barrel should work. Oil has been applied to the rig and two separate dies were applied. The finish is a satin sheen that allows for a moisture barrier. This rig is completely leather lined. The only thing you see when you look at the back is the thread and entry points to change the buckle. The ornamentation consists of nickel spots and a very special buckle set on the belt. The holster bands are laired between the top leather and lining so you do not see them from the back side. The hammer thongs were also configured in the same way. You will also notice that the buckle sets on the holsters match the buckle set on the gun belt Quote
Members johnny7 Posted January 18, 2008 Members Report Posted January 18, 2008 Beautiful work Larry. Quote
Cecil Posted January 18, 2008 Report Posted January 18, 2008 That is a real beauty. Brings back memories of my childhood. Quote
Members gunfighter48 Posted January 18, 2008 Members Report Posted January 18, 2008 (edited) Gorgeous work, just gorgeous. I grew up in the 50s so it does bring back memories of the cap gun holster that I played with back then. I used to do cowboy action shooting and would have been walking on cloud 9 to have a holster set like that!!!!!! John Edited January 18, 2008 by gunfighter48 Quote
Members skip Posted January 18, 2008 Members Report Posted January 18, 2008 very nice set up, I also liked your explanation of what you did and how you did it. watch the rubie crystals on the buckel as they have a tendency to get lost. again nice tooling and spot job! Quote
Contributing Member Jordan Posted January 18, 2008 Contributing Member Report Posted January 18, 2008 Fantastic and the time it took shows in the quality of the end product. What would the rig cost retail these days? I would guess 350 to 400 dollar range? Quote
Members bcurrier Posted January 18, 2008 Members Report Posted January 18, 2008 What would the rig cost retail these days? I would guess 350 to 400 dollar range? No smileys or anything. Were you kidding? Bill Quote
Ambassador Luke Hatley Posted January 18, 2008 Ambassador Report Posted January 18, 2008 (edited) LLASSO...ASWUM WORK A+++ JORDAN NOT TO BE UGLY OR ANYTHING, I WILL SPEAK FOR MY SELF A GOOD LEATHER CRAFTSMAN IS NOT GOING TO GIVE THEIR PRODUCTS AWAY... DOUBLE WHAT YOU ASKED.....AND I AM PROBABLY STILL OFF BY A LOT. WHAT SAY LLASSO ? Edited January 18, 2008 by Luke Hatley Quote
Members Tina Posted January 18, 2008 Members Report Posted January 18, 2008 This is just very, very amazing work you've done:-) Quote
Contributing Member Jordan Posted January 18, 2008 Contributing Member Report Posted January 18, 2008 (edited) It was just a guess and it is obvious I was way off. No insult intended and my experience around here is that most people are just plain cheap. Double my guess seems reasonable to me, but asking that much would be a difficult sale with a public that wants everything for free. Maybe elswhere in the country would be easier. Bianchi site lists some rigs at around 600 not sure if thats just for a belt or the whole rig? Edited January 18, 2008 by Jordan Quote
Members bcurrier Posted January 18, 2008 Members Report Posted January 18, 2008 A plain, but well-made, lined, mexican loop holster, double gunbelt is typically in the $350-$500 range. Buscadero gunbelts are more. Border stamping or basketweave adds to that. Carving adds a lot more. Two-tone dyeing adds again. Terrific rig! The only thing I don't like are the buckles - easy to change. Bill Quote
Billy P Posted January 18, 2008 Report Posted January 18, 2008 Wow, I thought as my mouth dropped open and my chin hit the shelf that holds the keyboard !! I have seen some other places try and make the Roy Rogers sets not as nice as yours Larry and they were asking $1000 or more for the custom work ie. fit, lining, etc. Now off to get my chin stitched up, Really nice work. Billy P Quote
Ambassador Beaverslayer Posted January 18, 2008 Ambassador Report Posted January 18, 2008 Larry, each time I see your work, I'm amazed even more. That is one BEAUTIFUL rig. Are you going to make matching spur straps? Ken Quote
Members llasso Posted January 18, 2008 Author Members Report Posted January 18, 2008 Fantastic and the time it took shows in the quality of the end product. What would the rig cost retail these days? I would guess 350 to 400 dollar range? This rig will sell for $950.00 to the right buyer Quote
Members llasso Posted January 18, 2008 Author Members Report Posted January 18, 2008 Beautiful work Larry. Thanks for the nice words Quote
Members llasso Posted January 18, 2008 Author Members Report Posted January 18, 2008 LLASSO...ASWUM WORK A+++ JORDAN NOT TO BE UGLY OR ANYTHING, I WILL SPEAK FOR MY SELF A GOOD LEATHER CRAFTSMAN IS NOT GOING TO GIVE THEIR PRODUCTS AWAY... DOUBLE WHAT YOU ASKED.....AND I AM PROBABLY STILL OFF BY A LOT. WHAT SAY LLASSO ? This rig should sell for $950.00. and that is a good price... I would like to get $1200.00 but that is not to be Larry Quote
Members llasso Posted January 18, 2008 Author Members Report Posted January 18, 2008 Thanks to all of you for the nice words. I do enjoy my work in leather and try to the best of my ability to make it as perfect as I can. IWorking with leather is a joy as you can make it what you want as you are the creator of the finished product. I hve made spur straps to match the gun belt, Quote
Members ericluther Posted January 18, 2008 Members Report Posted January 18, 2008 What a work of art!! amazing! Quote
ArtS Posted January 19, 2008 Report Posted January 19, 2008 That is beautiful craftsmanship! Someday I want to make one for myself and the saddle. I'm a big RR fan. Check out this link for one for sale on the RR site. Over $2500! http://www.royrogers.com/shop-index.html ArtS Quote
Members Myriam Posted March 21, 2008 Members Report Posted March 21, 2008 Just awesome work. Totally awesome. Hope I can get that good one day. Hope you found the right buyer! Quote
Members BWH Posted May 20, 2011 Members Report Posted May 20, 2011 Good Morning, Please find picture of the Roy Rogers Reproduction Gun Belt and Holster set I just finished. This rig took about 60 hours from start to finish. It is made from 8/9oz leather with 4/5oz leather lining. The belt is 3.5” wide and is set at 39” center it will go down to 37” and up to 41”. This rig is completely carved even under the billet straps and the holster flaps are also carved. I have attached a retention strap to this rig that is blind stitched. That means you do not see it from the front side of the belt. It also has two access entry points in the back of the belt that allow to change the buckle if you so desire.. These points allow the screws on the buckle to be sub- surface , so as not to mar the leather . There are hammer thongs on each holster. There are 36 bullet loops for 45 or 44 caliber bullets. The holsters are made for a Colt SAA 45, The toes of the holsters are open so any length barrel should work. Oil has been applied to the rig and two separate dies were applied. The finish is a satin sheen that allows for a moisture barrier. This rig is completely leather lined. The only thing you see when you look at the back is the thread and entry points to change the buckle. The ornamentation consists of nickel spots and a very special buckle set on the belt. The holster bands are laired between the top leather and lining so you do not see them from the back side. The hammer thongs were also configured in the same way. You will also notice that the buckle sets on the holsters match the buckle set on the gun belt Quote
Members cottoncreek Posted May 20, 2011 Members Report Posted May 20, 2011 (edited) Yep that is real good. Saw this and posted mine elsewhere. Edited May 21, 2011 by cottoncreek Quote
Members Leatherbaron Posted January 31, 2012 Members Report Posted January 31, 2012 Good Morning, Please find picture of the Roy Rogers Reproduction Gun Belt and Holster set I just finished. This rig took about 60 hours from start to finish. It is made from 8/9oz leather with 4/5oz leather lining. The belt is 3.5" wide and is set at 39" center it will go down to 37" and up to 41". This rig is completely carved even under the billet straps and the holster flaps are also carved. I have attached a retention strap to this rig that is blind stitched. That means you do not see it from the front side of the belt. It also has two access entry points in the back of the belt that allow to change the buckle if you so desire.. These points allow the screws on the buckle to be sub- surface , so as not to mar the leather . There are hammer thongs on each holster. There are 36 bullet loops for 45 or 44 caliber bullets. The holsters are made for a Colt SAA 45, The toes of the holsters are open so any length barrel should work. Oil has been applied to the rig and two separate dies were applied. The finish is a satin sheen that allows for a moisture barrier. This rig is completely leather lined. The only thing you see when you look at the back is the thread and entry points to change the buckle. The ornamentation consists of nickel spots and a very special buckle set on the belt. The holster bands are laired between the top leather and lining so you do not see them from the back side. The hammer thongs were also configured in the same way. You will also notice that the buckle sets on the holsters match the buckle set on the gun belt Well I would say "Shit hot gunbelts" i like em Terry Quote
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.