Members Caesar Posted March 13, 2018 Members Report Posted March 13, 2018 I try to be very gentle while scoring the leather on my first pass so that the ruler doesn't slide. Then I cut through on my second pass. I want to put something on the back of my ruler to keep it from sliding. Cork? Doesn't seem that I can find any thin enough. Something like this? Cotton Friction Tape I'm worried that it will leave marks on the leather. What do you use? Do you use anything? Quote
Members niakulah Posted March 14, 2018 Members Report Posted March 14, 2018 I use a large quilting ruler. They do make non-slip versions but mine's just a regular one. It doesn't slip very easily because of the huge surface area. It's also been a huge help in getting my corners square. Quote
Members Caesar Posted March 14, 2018 Author Members Report Posted March 14, 2018 4 minutes ago, niakulah said: I use a large quilting ruler. They do make non-slip versions but mine's just a regular one. It doesn't slip very easily because of the huge surface area. It's also been a huge help in getting my corners square. Thank you. I may look into this in the future. For now I'm looking more for something to put on the underside of my existing rulers / squares. Quote
Members Wedgetail Posted March 14, 2018 Members Report Posted March 14, 2018 Glue.... thin coat, let it dry thoroughly. Too thick or too wet and it may mark your leather or pull up the surface finish (practice on scrap). I use tanners bond contact cement. You can do the same thing to acrylic or wooden templates. Quote
Members Caesar Posted March 14, 2018 Author Members Report Posted March 14, 2018 1 minute ago, Wedgetail said: Glue.... thin coat, let it dry thoroughly. Too thick or too wet and it may mark your leather or pull up the surface finish (practice on scrap). I use tanners bond contact cement. You can do the same thing to acrylic or wooden templates. I'll try this. I use Barge Cement. I'm sure it works similarly. Thanks! Quote
Members Wedgetail Posted March 14, 2018 Members Report Posted March 14, 2018 3 hours ago, Caesar said: I'll try this. I use Barge Cement. I'm sure it works similarly. Thanks! No worries mate! It gave me an idea for another quick tip video for my youtube channel Quote
Members lonesome dove Posted March 14, 2018 Members Report Posted March 14, 2018 This is what I used. Thin with an adhesive back and inexpensive. https://www.amazon.com/gp/product/B0079XLR3A/ref=oh_aui_detailpage_o03_s02?ie=UTF8&psc=1 Hope this helps. Quote "Lonesome Dove" "I hate rude behavior in a man. I won't tolerate it."
Members Bolt Vanderhuge Posted March 14, 2018 Members Report Posted March 14, 2018 There are rulers that alrady have the cork installed. I got mine at Walmart. Though I do not always use it. Quote
Members Matt S Posted March 14, 2018 Members Report Posted March 14, 2018 I tend to only use the ruler to mark the leather with an awl, then cut the leather freehand using a knife. Usually a round knife or an Olfa wheel. My big ruler has a handle on it so I can press pretty hard to stop it from moving about. Cutting the leather in one pass makes for a much neater edge. Quote
garypl Posted March 14, 2018 Report Posted March 14, 2018 I have a 48” ruler bolted to the edge of my bench. I loosen the bolt on one side, slip the leather under the ruler and align it, then tighten the bolt. I press down on the ruler as I cut and it keeps the leather very secure while cutting. For obvious reasons it will not work with pieces too large to fit under the ruler. Gary Quote Cowboy 4500, Consew 206RB-4
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.