Members Jack1970 Posted September 30, 2018 Members Report Posted September 30, 2018 That's a beautiful bag! My construction is not great but I really want to make my wife a purse someday. Great work! Quote
Members battlemunky Posted September 30, 2018 Members Report Posted September 30, 2018 I'd hold off on the 2nd coat of NFO @Marietje unless you have several days to ensure it dries. Some folks do exactly like you did on the first one and skip the pre-dye NFO. It isn't a rule or anything and it will likely only make it a little bit softer. Your original bag above looks fantastic. I can pretty much only agree with everyone else, your choice of dye color and that contrast with the black stitching is great and the whole thing is just a lovey piece of work. Regarding your strap edges, the way I do mine is I sand them very close to where I want them, then use water the first run of slicking, then a thing coat of gum trag for the second slicking, then dye, and sometimes I'll go back and hit it with some beeswax. I can't wait to see the next one Quote
Members Garyspruill Posted October 2, 2018 Members Report Posted October 2, 2018 On 9/29/2018 at 4:56 PM, Marietje said: Thank you all for the kind and positive comments. @ Scoutmom103: It definitely can carry weight Lot's of unnecessary stuff I carry around.... LOL. I've got the pattern from DieselpunkRo @ Etsy. Lot's of nice DIY patterns. Dimensions are 12x6 inch, but you also get a larger pattern of 20x10 inch @ Riem: dankjewel. Yes I hand stitched. I like hand stitching, don't want to use a machine (don't have one, can't buy one either). That said, I'm looking into buying a good diamond chisel cause I like that more than the punched holes. Might be difficult with these patterns though, cause they are all perfectly aligned with the amount of holes. I used rubber cement for the lining. Yes, edges of the strap are more rough. It was a different piece of leather as I did not have a piece long enough and for some reason the flesh side was more rough too. Still figuring out how to get the edges real smooth. It's getting better with the next bag I think, just a lot of practice I need to do. I use a little gum trac now, then edge with my Dremel and an edger with different widths on it (via eBay) and then again with some bees wax. Next time I want to try some edge kote. It's still not as smooth as can be. I think I either use too much or not much enough gum trac? @Flashmojo & Sheilajeanne: yes correct, Fiebings Pro Saddle Tan @ScoobyNewbie: Color is mainly the dye, the pure neatsfoot did not do that much anymore, but I only applied 1 coat after dying. Luckily it's not that shiny because of the resolene. I was afraid too it would become to shiny. I've cut out all the pieces for the next bag, did the edges and applied two coats of pure neatsfoot now. It darkened a little, but still not much, so I think I'll do another coat tomorrow. Then I need to decide if I put mink oil on or carnauba creme, or maybe both? Any advice is appreciated! Marietje: I have made several bags from the patterns of DieselpunkRO and my wife loves all of them. :-) I was making the Witch Doctor Bag (pattern) for myeslf and when the wife saw it, she took ownership of it and I finished it for her (hmmmm?) I only "wish" I could figure out what he (Tony aka: DieselPunk) uses on the edges to darken them up and make them look patina (darker) like he does. The bag you made: looks fantastic! Great Job! When cutting out the leather, don't you just love all the stitching plugs EVERYWHERE? It took me days to get them all up from the floor:-) Your edges look fine. This is how they are suppose to look from the tutorial. Quote
RockyAussie Posted October 2, 2018 Report Posted October 2, 2018 Very nice work you should be proud, I know I would be. Quote Wild Harry - Australian made leather goodsYouTube Channel Instagram
ABHandmade Posted October 2, 2018 Report Posted October 2, 2018 I fully agree with @RockyAussie. Your bag is gorgeous! Quote
Members Harrycho Posted October 7, 2018 Members Report Posted October 7, 2018 Really nice work. Quote
Members Marietje Posted October 12, 2018 Author Members Report Posted October 12, 2018 On 2-10-2018 at 8:19 AM, Garyspruill said: Marietje: I have made several bags from the patterns of DieselpunkRO and my wife loves all of them. :-) I was making the Witch Doctor Bag (pattern) for myeslf and when the wife saw it, she took ownership of it and I finished it for her (hmmmm?) I only "wish" I could figure out what he (Tony aka: DieselPunk) uses on the edges to darken them up and make them look patina (darker) like he does. The bag you made: looks fantastic! Great Job! When cutting out the leather, don't you just love all the stitching plugs EVERYWHERE? It took me days to get them all up from the floor:-) Your edges look fine. This is how they are suppose to look from the tutorial. That is great to hear! (sorry for my delayed answer, for some reason I just don't get notifications of responses, so look at this forum occasionally). I love the patterns of Tony too! What's your name on his page? I'm Mary I just finished the Boston bag (maybe you have seen). Need to make better pictures and will post here too. Now I'm working on the Messenger bag. I've just watched a video from Armitage Leather on YouTube about edge burnishing. It's a skill I do not quite master yet. Armitage is using 2 kinds of burnishers though, 1 more rounded and one for the more flat edges. It is key that the burnisher touches the leather well. Haha.... the stitching plugs... it's a pain in the but! I have a piece of tape at hand to 'pick them up' and also a cup to put them in, as I have a simple punch that I can close off with my fingers and empty in the cup when needed. On this weekender bag I used edge burnishers in a Dremel tool, which made it a lot more convenient I must say, but still, they could be better. Quote Diplomacy is... telling someone to go to hell in such a way that he is actually looking forward to the trip...
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.