toxo Posted February 22, 2021 Report Posted February 22, 2021 Can anyone recommend some stuff that is thin enough to go into some small gaps, Goes off hard and will withstand a decent amount of heat? The walls on this thermocouple probe are so thin that it ripped apart when haf way into the hole. I have a replacement but I'd like to save that for a second project if I can. It's just a probe and the business end is already in the hole so I'm thinking if I fill the hole in and build up around it with some sort of putty, when it goes off I can drill & tap through the putty to hold it in place. Any ideas folks? Quote
Members Bigfoote Posted February 22, 2021 Members Report Posted February 22, 2021 try some JB weld, any hardware carries it. Quote
Members Tugadude Posted February 22, 2021 Members Report Posted February 22, 2021 Could you solder a metal sleeve over the existing metal sleeve? Just something to cover and beef it up? 1 minute ago, Bigfoote said: try some JB weld, any hardware carries it. I was concerned about JB Weld withstanding heat, so I looked it up. The info I saw says it can withstand 500 degrees Fahrenheit for sustained periods and a maximum of 600 degrees F. So it would be a great option so long as you don't exceed those numbers. Quote
toxo Posted February 22, 2021 Author Report Posted February 22, 2021 7 minutes ago, Tugadude said: Could you solder a metal sleeve over the existing metal sleeve? Just something to cover and beef it up? I was concerned about JB Weld withstanding heat, so I looked it up. The info I saw says it can withstand 500 degrees Fahrenheit for sustained periods and a maximum of 600 degrees F. So it would be a great option so long as you don't exceed those numbers. I was just looking at the JB heat stuff. Promising. Hadn't thought of soldering. If the JB can hold it together it wouldn't be too hard to make a couple of half inch straps with cut outs to go around the cable one on top of the other and drill & tap or solder either side. Thanks guys. Quote
Contributing Member fredk Posted February 23, 2021 Contributing Member Report Posted February 23, 2021 I'll second JB Weld. I used some as a 'temporary' repair on a valve cover and on a water outlet on my 1930 Austin 7, that was 20 years ago and the JB is still holding. The valve cover is under the exhaust so it gets really hot there. The water through the outlet only gets to about 90 degrees. Quote
Members 327fed Posted February 23, 2021 Members Report Posted February 23, 2021 Used to be a more industrial version called Devcon. Also Liquid Steel and Liquid Aluminum. Quote
Members chrisash Posted February 23, 2021 Members Report Posted February 23, 2021 There is a special high heat version of JB Weld see here JB Weld 37901 ExtremeHeat High Temperature Resistant Metallic Paste-3 oz: Amazon.co.uk: Car & Motorbike Quote
toxo Posted February 23, 2021 Author Report Posted February 23, 2021 Thanks guys. I've ordered some JB, will be here tomorrow. Temp should be ok for foiling, Not sure about the higher temps for heat embossing but once I've strapped it down I don't think it'll be an issue, (famous last words right?) Watch this space or rather watch the updates on my DIY hot stamp buid. Quote
CFM chuck123wapati Posted February 23, 2021 CFM Report Posted February 23, 2021 12 hours ago, fredk said: I'll second JB Weld. I used some as a 'temporary' repair on a valve cover and on a water outlet on my 1930 Austin 7, that was 20 years ago and the JB is still holding. The valve cover is under the exhaust so it gets really hot there. The water through the outlet only gets to about 90 degrees. i'll third it! I have a75 mgb with some jb parts also. i use it alot. Quote
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.