Jump to content

Recommended Posts

  • Members
Posted

I bought mine from Toledo Industrial Sewing machines, and it has ran like a top for over a year now. This is the first time I have seen a complaint about the motor, but hearing Made in China electronics suddenly broke doesn't surprise me much.

Yes thats where I planned on getting mine as well. ABout how long did it take to get to you?

  • Replies 96
  • Created
  • Last Reply

Top Posters In This Topic

  • Members
Posted

Talked to Bob on the phone one afternoon, and he mailed it the next morning. I think it took 2-3 days to get here. I've ordered from Bob 3-4 times and never had any issues.

  • Members
Posted

I have 5 of those on machines here and must have installed 20 or more in the past 3 years. I did get one that never ran at all right out of the box. Bob replaced it no questions asked.

  • Moderator
Posted

I have bought 4 Family Sew 550s motors from Toledo Industrial and have had no problems at all. They usually arrive in one or two business days, depending on what time you order (re: UPS truck pickup time). Two are on 441 machines and two on walking foot machines, one of which I sold.

The only caveat I discovered is that they work better if you pull the lever straight down, rather than on an angle. Pulling on an angle flexes the shaft and sensor and can cause a slowdown at the end of travel, just when you expect more speed.

Posted IMHO, by Wiz

My current crop of sewing machines:

Cowboy CB4500, Singer 107w3, Singer 139w109, Singer 168G101, Singer 29k71, Singer 31-15, Singer 111w103, Singer 211G156, Adler 30-7 on power stand, Techsew 2700, Fortuna power skiver and a Pfaff 4 thread 2 needle serger.

  • Members
Posted

Talked to Bob on the phone one afternoon, and he mailed it the next morning. I think it took 2-3 days to get here. I've ordered from Bob 3-4 times and never had any issues.

I have 5 of those on machines here and must have installed 20 or more in the past 3 years. I did get one that never ran at all right out of the box. Bob replaced it no questions asked.

I have bought 4 Family Sew 550s motors from Toledo Industrial and have had no problems at all. They usually arrive in one or two business days, depending on what time you order (re: UPS truck pickup time). Two are on 441 machines and two on walking foot machines, one of which I sold.

The only caveat I discovered is that they work better if you pull the lever straight down, rather than on an angle. Pulling on an angle flexes the shaft and sensor and can cause a slowdown at the end of travel, just when you expect more speed.

Nice. Glad to know they ship quick!!!

Yes, I've heard a lot of good things this servo and Bob. He was who I was gonna originally get my sewing machine from but I found another one before he got around to servicing one at his shop.

Wiz crafts, I wish I knew what lever you were talking about, but I don't. Never sewn anything ever, this will be my first sewing machine (consew 206rb) and first time installing a servo motor. All I currently care about is that it works lol. I hope to become as knowledgable as many of you... I'm just taking it one step at a time. I'm gonna order my servo tomoro. Trying to gather all the tools I think I will need to disassemble the clutch so I can get it up more stairs more easily on Wednesday... Then tackle putting the servo on. Thanks everyone!

  • Moderator
Posted

Wiz crafts, I wish I knew what lever you were talking about, but I don't. Never sewn anything ever, this will be my first sewing machine (consew 206rb) and first time installing a servo motor.

The FS-550s has a plastic activator lever facing forward when the motor is mounted under a standard sewing machine table. The lever moves down to release the brake and increase the speed. Just make sure that the rods or chain you use to connect it to the floor pedal are routed as straight vertically as possible. This is usually not a problem on walking foot machines, as the floor pedal sits pretty much under the left edge of the motor and control lever.

Posted IMHO, by Wiz

My current crop of sewing machines:

Cowboy CB4500, Singer 107w3, Singer 139w109, Singer 168G101, Singer 29k71, Singer 31-15, Singer 111w103, Singer 211G156, Adler 30-7 on power stand, Techsew 2700, Fortuna power skiver and a Pfaff 4 thread 2 needle serger.

  • Members
Posted

Nice. Glad to know they ship quick!!!

Yes, I've heard a lot of good things this servo and Bob. He was who I was gonna originally get my sewing machine from but I found another one before he got around to servicing one at his shop.

Wiz crafts, I wish I knew what lever you were talking about, but I don't. Never sewn anything ever, this will be my first sewing machine (consew 206rb) and first time installing a servo motor. All I currently care about is that it works lol. I hope to become as knowledgable as many of you... I'm just taking it one step at a time. I'm gonna order my servo tomoro. Trying to gather all the tools I think I will need to disassemble the clutch so I can get it up more stairs more easily on Wednesday... Then tackle putting the servo on. Thanks everyone!

I put one on my Consew 206, makes sewing super easy because of the speed control, plus its much quieter than that old clunker of a clutch motor. Seriously, the clutch motor on mine weighed a good 50-60 lbs.

https://youtu.be/t9y5RoogvYo

  • Members
Posted

The FS-550s has a plastic activator lever facing forward when the motor is mounted under a standard sewing machine table. The lever moves down to release the brake and increase the speed. Just make sure that the rods or chain you use to connect it to the floor pedal are routed as straight vertically as possible. This is usually not a problem on walking foot machines, as the floor pedal sits pretty much under the left edge of the motor and control lever.

Thanks! I will try to figure all this out as I go along using this info and info from other members!

I put one on my Consew 206, makes sewing super easy because of the speed control, plus its much quieter than that old clunker of a clutch motor. Seriously, the clutch motor on mine weighed a good 50-60 lbs.

https://youtu.be/t9y5RoogvYo

Yea colt your video pretty much sold me on it so thanks for that! Do you have a list of tools you know a person would need to remove the clutch/install the servo? Im going to pick up the machine tomoro and Ill be lugging it up stairs, after I test it I planned on taking the clutch off to make travel easier?? Thanks

ALSO! Does anybody have a IN STORE suggestion for machine oil??? I dont have access to lily right now i just need something between now and tomoro as this machine has been sitting! THANKS! :)

  • Members
Posted (edited)

MG, this is based on my removing/replacing 3 clutch motors. Basic tools - a couple of spanners, because you don't know the size of the nuts you can either take a set of spanners or a couple of adjustable wrenches, a medium to biggish one for the nuts holding the motor on and a smaller one for the bolts on the pedal-motor linkage. A couple of screwdrivers to remove the switch box. It will be held on with either slotted or Philips head screws (use long shank if you can, just in case). Pair of pliers to remove any cable clips.

Procedure - unplug power cord (!) and remove switch box. Remove any clips holding the power cable to the table. Disconnect pedal linkage. Remove drive belt. Loosen the three nuts holding the motor on and let the motor hang down on the bolts. While supporting the motor remove the single nut at the front then slide the motor out from the remaining two bolts.

Done.

As for the oil question (I love oil questions!!!!) at the risk of starting a flaming war if you've got 3-in-1 oil handy use that. Much is written about oils, and much of what is written is irrelevant (and oft-times rubbish). Basically, all you really want is a thinnish oil. Auto Trans Fluid is actually quite good as a thin oil (it was originally developed as a replacement for Sperm Whale oil, which is considered by many to be one of the better lubricating oils - but obviously you can't get it any more). Just don't get yourself into a knot over oils as most of them aren't anything special (regardless of what the manufacturer might tell you - MSDS is your friend :) ).

Edited by dikman

Machines wot I have - Singer 51W59; Singer 331K4; Seiko STH-8BLD; Pfaff 335; CB4500.

Chinese shoe patcher; Singer 201K (old hand crank)

  • Members
Posted (edited)

I would suggest that there is an enormous body of experience that discourages the use of either WD-40 or 3-in-1 oil in sewing machines, guns, fishing reels....anything which will be sensitive to gummy or hygroscopic shellac deposits over time. There is nothing easier to get than ordinary sewing machine *white* oil. Avoid any gimmick oil that is suspended in a volatile carrier, as the carrier evaporates over time and leaves lord-knows-what behind. Any machines with ball or roller bearings should not use an oil with moly additives.

-DC

Edited by SARK9

Machines: Juki LU-563, Consew 206-RB5, Singer 20U33, Pfaff 481, Mitsubishi CU-865-22, Consew 29B, Rebadged Juki LU-562,  Mitsubishi LS2-180,  Seiko SK-6, Juki LG-158-1

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.


×
×
  • Create New...