Jump to content

Recommended Posts

  • Members
Posted

Hi. I just purchased a consew dcs s4. The store said it was new...charged me 1095 for it. I drove three hours to pick up from sewing machine.com in Atlanta ga. So I noticed that the table it was on wasn’t new and it was a singer table. Had a worn look to it but I dont care about the table. When I got home I didn’t have time to do anything. The next day my husband and I decide to give it a look over and see how to use it. Long story short...I know it’s a learning phase for this machine..but the leather doesn’t move smoothly at all and kept bunching. I decided to look under the machine. I saw a small chip on the cutting side of the blade..further inspection I found two more! So I’m thinking there is no way this is a new machine and I don’t think sharpening the blade will fix these nicks. So I would have to buy another blade then drive three hours one way to have the same company put a new blade in a machine I have had for 3 days! Will sharpening take the nicks out? Am I overreacting to want to return the machine? I was financing it with 12 months no interest....

986DF452-8FE3-4044-AE3D-9CE3593530B8.jpeg

  • Replies 31
  • Created
  • Last Reply

Top Posters In This Topic

Posted

Those nicks should sharpen out alright.Just off the top of my head the bell starts at about 2" wide and I normally replace mine when they get down to about 1" or a bit more. I would like to see a few more pictures all the same of the sharpening stone, where you have your foot set to in relation to the blade and the angle of the stone in relation to the bell blade and so on.

WH.jpgWild Harry - Australian made leather goods
YouTube Channel
Instagram

  • Members
Posted

Ok. I’m going to go and take more pictures. I am going to call the place still and express how I feel I’m paying a new price for a used machine! Maybe they will knock off some off the price. If they don’t I will insinuate I will be returning it ..hope that works out lol.

Posted (edited)
7 minutes ago, JeannieH said:

Ok. I’m going to go and take more pictures. I am going to call the place still and express how I feel I’m paying a new price for a used machine! Maybe they will knock off some off the price. If they don’t I will insinuate I will be returning it ..hope that works out lol.

Alright ...but a wrong set up and sometimes some leather types as well will cause this and you may want them for help at some future time. I would give us a chance to see the other pictures first myself. Brian

Did you get a dressing stone stick with it?

Edited by RockyAussie
I forgot to ask something

WH.jpgWild Harry - Australian made leather goods
YouTube Channel
Instagram

  • Members
Posted

Ok. Yes I got the dressing stone stick but I didn’t get the deburring stone..or the 25mm foot..or the hinge screws and washer for installing the guide...things a new machine should have right lol!

F48A2FDE-B7A1-49EF-89F9-A2AADE648695.jpeg

5A14BDA8-4452-49A9-8E13-8D918375754B.jpeg

60D041C2-EFF5-4D64-8B9B-00EAB18165EB.jpeg

Posted

AQ few further back pics would be good ...but it does not apear to be all that new so far. The bell is a little too close to the foot. Once you sharpen out those nicks it will be about right though. The feed stone is sitting down too low and should be very nearly touching the bell inside.One turning knob on the left at the front will alow angle changes and on the left side there is an adjustment set up to allow you to move the stone upward. There are a few you tubes out there on how to do these adjustments and I would check them out first. I will look some up and give you some links tomorrow. My dinners ready NOW i'm told. :lol:

WH.jpgWild Harry - Australian made leather goods
YouTube Channel
Instagram

  • Members
Posted

I emailed them to see if they would adjust the pricing to match the condition. We will see. Ok I will send pics further away. Yes I’ve watched videos before I even turned it on. I will try sharpening when my kids wake up. I will be using it on leather 2-6 ounze. Enjoy your dinner and I will make adjustments like you mentioned. Thanks for helping me!

Posted

On the last pic it looks like it is just some metal burrs from sharpening that could be taken off by running your stick on it.

Bob Kovar
Toledo Industrial Sewing Machine Sales Ltd.
3631 Marine Rd
Toledo,Ohio 43609
1-866-362-7397

toledo-banner-2.jpg

  • Members
Posted

Problem is I don’t have the stick to do that! They will let me bring it back but are trying to persuade me to let them send me the missing pieces and a new blade. I rather return it and get a new one when they get them in. I see that replacing a blade is not an easy job.

  • Members
Posted

What are some other affordable skiving machines in the price range as the consew? That offers financing? If this consew isn’t a good machine I rather return it and find something else. 

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.


×
×
  • Create New...