Jump to content

Recommended Posts

Posted

I have been doing a few projects recently that need a very small cylinder machine to enable me to get into the tight corners and such. This is still a bit of a work in progress but so far the results have been good. A few more tweaks and they should be excellent. I have a 335 Pfaff , 69 Adler, Tk 335 Elizabeth and a 331 Pfaff that I have finished of some new cylinder caps for. After doing some measurements and tests the width of the caps have now been reduced from 46.6mm down to 41.4mm. ( a bit under 1/4"). The depth has reduced a couple of mm and the length a couple as well. NOTE: except for the Pfaff 331 which has a little more room for reductions, all of the caps fitted and they are all the smaller bobbin variety.

The first picture shows 3 of the 4 caps just finished as against the ones being replaced.

DSC04651_resize.JPG

This is the TK335  Elizabeth cylinder showing some comparisons.

DSC04659_resize.JPG

DSC04660_resize.JPG

DSC04656_resize.JPG

DSC04658_resize.JPG

This one below shows the Adler 69 fitted well

DSC04665_resize.JPG

DSC04664_resize.JPG

This one below on my favourite Pfaff 331machine (needle and dog foot feed and no pesky walking foot)

DSC04677_resize.JPG

DSC04678_resize.JPG

Here are a couple of samples of work where this kind of reduction comes in handy. I do like to be able to stitch around a product fully and try to design for this and the sewing machines capability.

DSC08099_resize.JPG

DSC08108_resize.JPG

DSC04676_resize.JPG

Here I think the difference shows fairly well

DSC04675_resize.JPG

If any of you have printers and one of these style machines let me know and I will get you a stl file if you want it.

If you have one of these machines and are one of my followers and do not have a printer... PM me if you would like one.

I know the colour is awful and I could have done them in a metalic silver colour but at least they are easy to find now.

Brian

 

 

WH.jpgWild Harry - Australian made leather goods
YouTube Channel
Instagram

  • Replies 55
  • Created
  • Last Reply

Top Posters In This Topic

Top Posters In This Topic

Posted Images

  • Members
Posted

Mate, you never cease to amaze me! I wouldn't mind the Pfaff 335 version as my cap has been modified slightly so a spare would be nice.:wave:

Machines wot I have - Singer 51W59; Singer 331K4; Seiko STH-8BLD; Pfaff 335; CB4500.

Chinese shoe patcher; Singer 201K (old hand crank)

Posted
54 minutes ago, dikman said:

Mate, you never cease to amaze me! I wouldn't mind the Pfaff 335 version as my cap has been modified slightly so a spare would be nice.:wave:

File sent in PM .

WH.jpgWild Harry - Australian made leather goods
YouTube Channel
Instagram

  • Members
Posted

And received. Ta very much.

Machines wot I have - Singer 51W59; Singer 331K4; Seiko STH-8BLD; Pfaff 335; CB4500.

Chinese shoe patcher; Singer 201K (old hand crank)

  • Members
Posted

Done. Looks much neater than the original (well, my original, at least).

 

Pfaff cover a.jpg

Machines wot I have - Singer 51W59; Singer 331K4; Seiko STH-8BLD; Pfaff 335; CB4500.

Chinese shoe patcher; Singer 201K (old hand crank)

  • Members
Posted

If someone needs an original cap - I still have 2 of them ;)

IMG_6196.JPG

~ Keep "OLD CAST IRON" alive - it´s worth it ~

Machines in use: - Singer 111G156 - Singer 307G2 - Singer 29K71 - Singer 212G141 - Singer 45D91 - Singer 132K6 - Singer 108W20 - Singer 51WSV2 - Singer 143W2

  • Members
Posted

They look nicer than mine - but the plastic one will be fine, it cost me almost nothing to make and I can easily make another if I need to.:)

Machines wot I have - Singer 51W59; Singer 331K4; Seiko STH-8BLD; Pfaff 335; CB4500.

Chinese shoe patcher; Singer 201K (old hand crank)

Posted
19 hours ago, dikman said:

Done. Looks much neater than the original (well, my original, at least).

 

Pfaff cover a.jpg

WOW that was quick. Looks better than my yellow coloured ones. I am hoping that a few of the other members that have clones of these machines will try them out for fitting. I would like to have a list of the various machines clones etc that it will fit onto to advise everyone. Also if there are any negatives as to where the cap may be improved. For 27 cents of filament electricity included. its not that big a risk really. So far mine have tested in use well and I will do a few more  little changes once I am confident it will fit a wide range of other clones as well. I am thinking of putting this thread into the sewing machine section in order to get some more feedback. Thanks for the feed back.

Brian

WH.jpgWild Harry - Australian made leather goods
YouTube Channel
Instagram

  • Members
Posted

I thought the yellow might be to match the Ducky in your profile pic :rolleyes:

Posted
6 minutes ago, Scoutmom103 said:

I thought the yellow might be to match the Ducky in your profile pic :rolleyes:

Ha Ha good one.... I started using this colour awhile back due to my super messy workbenches and just old age and bad memory. I think I spend more time looking for something than I do making stuff sometimes these days........What was i going to say.......Ogh well it'll be there somewhere.

WH.jpgWild Harry - Australian made leather goods
YouTube Channel
Instagram

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.


×
×
  • Create New...