Jump to content

Recommended Posts

Posted

I been thinking that we should have a file repository for making it easy for people to find anything that might be of use to them for laser or 3d printing. I will start this of with a small stl file which comes in useful for both these technologies. It should take about 5 minutes each to print and weighs 1Gram which is less than 5c each. The magnets can be found on ebay easily enough such as this one - https://www.ebay.com.au/itm/Super-Strong-N35-Round-Disc-Neodymium-Mini-Fridge-Magnets-Rare-Earth-New/333227699575?hash=item4d95eb2d77:g:EaUAAOSwTfFbTxto&frcectupt=true

From where I see it, that is about 27c US each if you get a hundred.

This is for a holding magnets and make them easy to remove from the job due to the shape that it has. It is designed for 9x3mm magnets that get superglued in after the print. If it is tight a little heat should work well usually. The picture below shows how I use them on the laser to hold down anything in place as it cuts. A quick tip here is to do a double or multiple cut allowing a stop between cuts as this shows areas on the run which may want to be held down more closely.

Here is the stl file - Laser magnet holders.stl

DSC05846.JPG

You can play darts with them onto your fridge if the missus isn't watching too.:P

I will try and load another new one again tomorrow.

Please feel free to load any files on to contribute.

If you would like to donate anything at all for the use of any of these files of mine at least please donate it to this Leatherworker forum that provide so well a way for us all to share. If you are not already a contributing member that would also be a great way to go.:thumbsup:

WH.jpgWild Harry - Australian made leather goods
YouTube Channel
Instagram

  • Replies 31
  • Created
  • Last Reply

Top Posters In This Topic

  • Members
Posted

Good idea about the "repository" as there have been other files posted that are scattered in other posts.

Machines wot I have - Singer 51W59; Singer 331K4; Seiko STH-8BLD; Pfaff 335; CB4500.

Chinese shoe patcher; Singer 201K (old hand crank)

  • Members
Posted

Hi guys, good idea Brian, these files are for a small guide i have been using while waiting on a decent pfaff one to turn up, it is used on the small plate that is screwed on the side of the arm and was very useful. I don´t know if you can use it on other machines? It swings in and out letting you turn etc. The other is the oil box that goes underneath as mine was missing, you will just need to drill the holes. The other one is the small arm plate that goes with the accessory plate with a lip to rest it on. You could just cut it off if not needed.

Pfaff guide 3.stl

Pfaff guide arm2.stl

Pfaff oil box1.stl

335pl.stl

 

Posted
11 hours ago, jimi said:

Hi guys, good idea Brian, these files are for a small guide i have been using while waiting on a decent pfaff one to turn up, it is used on the small plate that is screwed on the side of the arm and was very useful. I don´t know if you can use it on other machines? It swings in and out letting you turn etc. The other is the oil box that goes underneath as mine was missing, you will just need to drill the holes. The other one is the small arm plate that goes with the accessory plate with a lip to rest it on. You could just cut it off if not needed.

Pfaff guide 3.stl

Pfaff guide arm2.stl

Pfaff oil box1.stl

335pl.stl

 

Thanks for sharing @jimi . Have you got any pictures to add to that. I will throw in the stl 335 bobbin cover end caps later today when I have a bit more time.

WH.jpgWild Harry - Australian made leather goods
YouTube Channel
Instagram

  • Members
Posted

Here are a couple of anti spill dye holders for the small bottles

 

Eco-Flo 130ml anti spill stand v2.stl

The images, seems I cannot upload Fiebings stl as over 1.46m

Eco-Flow-spill-stand-No2.jpg

fiebings-No3.jpg

Mi omputer is ot ood at speeling , it's not me

  • Members
Posted (edited)

Updated Zip file format

Fieberg anti spill tray v2.zip

Edited by chrisash
changed zip format

Mi omputer is ot ood at speeling , it's not me

  • Members
Posted

Thanks Chris, no excuses for dye all over the place now!

20200713_104930.jpg.7a9b9b3169306ca2f81341c239fae712.jpg20200713_105052.jpg.1c1bbc7c799c3adc2d34def38946386f.jpg

Posted

Here are the stl files for the old casting 335 pfaff and 69 adler bobbin end cover caps. They are the same -

Adler Bobbin Cover.stl

This one is for those rare 331 Pfaff cylinder arm machines Pfaff 331 Bobbin Cover.stl

This first picture shows the reduced size across all 3 versions.DSC04650_resize.JPG

This one may show better still on a 331 style 

DSC04673_resize.JPG

DSC04671_resize.JPG

I will load a 49 piece bobbin holder case tomorrow if I get time

Cheers for now.

 

 

 

WH.jpgWild Harry - Australian made leather goods
YouTube Channel
Instagram

  • Members
Posted

Thanks Brian, Looks like you got some funky lollipop yellow 335´s in you shop now :lol:

Posted

This one is a bobbin holding case that will take 49 bobbins with the bobbin holes being 22x11mm. I have made it so that it would be easy to pick up the bobbin wanted due to the space between them as shown in the below picture.

Here find the stl file - BOBBIN CARRIER.stl

DSC03609_resize.JPG

WH.jpgWild Harry - Australian made leather goods
YouTube Channel
Instagram

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.


×
×
  • Create New...