DieselTech Report post Posted March 16 2 hours ago, quiltedlumber said: I am just a hobbyist and found a 10 pack of extra bobbins was nice to have . I keep 2 each of my popular colors or thread size available , so if you run out or coming close you don't have to stop and go through the winding process. You will need to do some searching to find a reasonable price but I found it was worth a extra dollars. I always have a few if not more empty and ready to go , so I can do a one off without wasting thread. Thanks. I ended up ordering 6, so now I have a total of 10 bobbins. Quote Share this post Link to post Share on other sites
dikman Report post Posted March 16 I bought 6 extra ones - then found the 6 I already had in another draw! Oil, you can either get the Lillywhite oil or just get some light hydraulic oil (ISO 32), it's basically the same stuff. Quote Share this post Link to post Share on other sites
DieselTech Report post Posted March 17 To all you Cobra class 4 owners. Have any of you had to replace any parts on your machine? Like springs or screws or any hard parts like a complete shuttle hook assembly? Thanks. Quote Share this post Link to post Share on other sites
dikman Report post Posted March 17 Geez, you're becoming paranoid about the machine! I haven't read too many reports of people having to replace busted bits on these machines (actually, I can't think of any off-hand). Quote Share this post Link to post Share on other sites
DieselTech Report post Posted March 17 (edited) 6 hours ago, dikman said: Geez, you're becoming paranoid about the machine! I haven't read too many reports of people having to replace busted bits on these machines (actually, I can't think of any off-hand). No not paranoid. Just dont like getting caught with my pants down. I just asked because if there was springs or parts that get weak or wear out. I would like to keep them parts on hand. Edited March 17 by DieselTech Quote Share this post Link to post Share on other sites
LiftPig Report post Posted March 17 (edited) Sorry this took so long to post. The top rows are the S point. The bottom two rows are TRI points. #25 needle. I have to say I’m not thrilled with the S point look. 277 thread top and bottom through 24oz of Hermann Oak veg Edited March 17 by LiftPig Add details Quote Share this post Link to post Share on other sites
LiftPig Report post Posted March 17 14 hours ago, DieselTech said: To all you Cobra class 4 owners. Have any of you had to replace any parts on your machine? Like springs or screws or any hard parts like a complete shuttle hook assembly? Thanks. Be careful with the screw holding the bottom feed dog in. It’s crazy tight and easy to strip. The screw holding the needle bar is the same. But I’m betting you have experience with that so it shouldn’t be an issue. Quote Share this post Link to post Share on other sites
DieselTech Report post Posted March 18 Guys & gals look at these super sexy stainless steel pieces of sewing machine porn. Excellent machine work, just pieces of beauty. Now I need the machine to get here to try them out. Quote Share this post Link to post Share on other sites
MarshalWill Report post Posted March 18 They are fine looking. Did you order them or make them? Quote Share this post Link to post Share on other sites
DieselTech Report post Posted March 18 5 minutes ago, MarshalWill said: They are fine looking. Did you order them or make them? I ordered them from a great company & also a member from here. They are from Hennigan Engineering & Precision. Super nice accessories. Quote Share this post Link to post Share on other sites
MarshalWill Report post Posted March 18 10 minutes ago, DieselTech said: I ordered them from a great company & also a member from here. They are from Hennigan Engineering & Precision. Super nice accessories. Thanks. I'll make a note of that. I'll probably be getting a machine later this year. Quote Share this post Link to post Share on other sites
DieselTech Report post Posted March 18 11 minutes ago, MarshalWill said: Thanks. I'll make a note of that. I'll probably be getting a machine later this year. No problem. I hope you find the machine you are looking for. Quote Share this post Link to post Share on other sites
WendlingKnives Report post Posted March 18 Looks like you and i are both eagerly awaiting our Cobras. Mine was supposed to have shipped today. Then its off with the Boss, and on to faster, easier stitching Quote Share this post Link to post Share on other sites
MarshalWill Report post Posted March 18 38 minutes ago, DieselTech said: No problem. I hope you find the machine you are looking for. Thanks, I will. We're planning a move and I'm not buying anything I will have to move. Machinery and such will happen after we're all situated. Quote Share this post Link to post Share on other sites
DieselTech Report post Posted March 19 3 hours ago, WendlingKnives said: Looks like you and i are both eagerly awaiting our Cobras. Mine was supposed to have shipped today. Then its off with the Boss, and on to faster, easier stitching Congrats on the new machine. Yeah I imagine the cobra will be a touch faster than the Tippman Boss. Yeah I figure my machine is at least 4 weeks out yet. Quote Share this post Link to post Share on other sites
LiftPig Report post Posted March 19 19 hours ago, DieselTech said: Guys & gals look at these super sexy stainless steel pieces of sewing machine porn. Excellent machine work, just pieces of beauty. Now I need the machine to get here to try them out. Hold the phone! Are those holster plates WITH feed dogs?!? Take my money! Quote Share this post Link to post Share on other sites
DieselTech Report post Posted March 19 (edited) 1 hour ago, LiftPig said: Hold the phone! Are those holster plates WITH feed dogs?!? Take my money! Yes they are!!! Narrow slot needle plates & feed dogs. 1 of them is the holster plate. The other 2 are narrow slot flat needle plates & feed dogs. Edited March 19 by DieselTech Quote Share this post Link to post Share on other sites
MarshalWill Report post Posted March 19 1 hour ago, DieselTech said: Yes they are!!! Narrow slot needle plates & feed dogs. 1 of them is the holster plate. The other 2 are narrow slot flat needle plates & feed dogs. That is outstanding. The prices aren't bad, either. Thanks for posting about these. Quote Share this post Link to post Share on other sites
DieselTech Report post Posted March 19 22 minutes ago, MarshalWill said: That is outstanding. The prices aren't bad, either. Thanks for posting about these. Yeah I ordered the cobra class 4 premium package & should of just bought the base package, then added the Hennigan Engineering needle plates & feed dogs. I could have saved a good chunk of change doing that. Lmao I'm blind, leading the blind man, going yeah I need this & that. When I actually have no clue what I all will need. Quote Share this post Link to post Share on other sites
MarshalWill Report post Posted March 19 26 minutes ago, DieselTech said: Yeah I ordered the cobra class 4 premium package & should of just bought the base package, then added the Hennigan Engineering needle plates & feed dogs. I could have saved a good chunk of change doing that. Lmao I'm blind, leading the blind man, going yeah I need this & that. When I actually have no clue what I all will need. I'll remember to order a base package if I go for a new machine. thanks for pointing that out. I think we all manage to get some things we don't need when stepping forward. Maybe you can sell the things you find you don't need and recoup some of the initial outlay. Quote Share this post Link to post Share on other sites
dikman Report post Posted March 19 4 hours ago, DieselTech said: Yeah I ordered the cobra class 4 premium package & should of just bought the base package, then added the Hennigan Engineering needle plates & feed dogs. I could have saved a good chunk of change doing that. Lmao I'm blind, leading the blind man, going yeah I need this & that. When I actually have no clue what I all will need. It's easy to get carried away with shiny new toys! Quote Share this post Link to post Share on other sites
JLSleather Report post Posted March 20 10 hours ago, LiftPig said: Hold the phone! Are those holster plates WITH feed dogs?!? I didn't find I use the "holster" or "stirrup" plates nearly as much as I thought I would. With just a little thought, the standard plate does prett much all of that. I suppose if you were trying to sew next to a metal clip.... Quote Share this post Link to post Share on other sites
DieselTech Report post Posted March 20 3 minutes ago, JLSleather said: I didn't find I use the "holster" or "stirrup" plates nearly as much as I thought I would. With just a little thought, the standard plate does prett much all of that. I suppose if you were trying to sew next to a metal clip.... Yeah I got a lot to learn on this beast. I've watched a few vids where they say the stirrup plate is good for sewing gussets on a 90° corner. For bags & such. Quote Share this post Link to post Share on other sites
JLSleather Report post Posted March 20 2 minutes ago, DieselTech said: Yeah I got a lot to learn on this beast. I've watched a few vids where they say the stirrup plate is good for sewing gussets on a 90° corner. For bags & such. yeah, prolly work there, long as the land is wide enough. Mostly on chrome-tanned bags, I would think. Assuming we're talking about the same type of bag, a 90° on a veg-tanned edge would likely cause a "booger" (wrinkle) I would find unacceptable. Still, it may be of use for like gussets on notebooks/binders? Quote Share this post Link to post Share on other sites
DieselTech Report post Posted March 20 7 minutes ago, JLSleather said: yeah, prolly work there, long as the land is wide enough. Mostly on chrome-tanned bags, I would think. Assuming we're talking about the same type of bag, a 90° on a veg-tanned edge would likely cause a "booger" (wrinkle) I would find unacceptable. Still, it may be of use for like gussets on notebooks/binders? Yeah I wish I could find more sewing vids of the cobra class 4. I found a few where they are sewing a project up. I just like watching them, to get a idea how things are done. Quote Share this post Link to post Share on other sites
