Jump to content

Recommended Posts

  • Members
Posted

I have a new cylinder arm machine and the flat bed accessory purchased at the same time. The table doesn’t fit very well and I’m afraid of ruining it completely if I start cutting on it. It’s hard to get a good photo of the fit issues, but can you see anything obvious that I’m missing? I know I need to cut off the back side near the belt, because it’s actually touching the belt. The left-most bolt in the front interferes with the knee lift. There are a couple places  near the point where the arm joins the body of the machine that there is a cutout that doesn’t follow the contour of the machine. I guess I looked and lusted after Uwe’s tables too much, but I really expected this one to be more useable than it is. Any tips and observations appreciated before I left my husband start cutting on it tomorrow. 

I think I’ll have to add each photo separately. This one is the back of the machine, where the belt rubs on the table. 

51D66191-B432-4499-931F-D08853B7BEA7.jpeg

  • Replies 20
  • Created
  • Last Reply

Top Posters In This Topic

Top Posters In This Topic

Posted Images

  • Members
Posted (edited)

Hi, I would talk with the seller before you cut up the table and get a refund?? It looks like it could be for another type of machine and not yours.

Edited by jimi
Posted

I had to move one of the bolt holes in the table of my CB4500.  Wasn’t a problem, but still a little annoying.  Worked fine afterward.  I would also contact the seller - looks like you may have a defective table.

Gary

Cowboy 4500, Consew 206RB-4

  • Members
Posted

That is a very shoddy workmanship for a flatbed table attachment.  I would send it back and make my own.  I would be embarrassed to sell that attachment.  Bush league!!!!

glenn

  • Members
Posted

Was this a new factory table attachment, its clear it has some really rough contour. 

As you mentioned, in other words, an after market quality attachment, by Uwe would be nice. 

  Here though, there are few but still comparisons with Uwes table attacments and these other factory brands. I believe its they are for sew machines, thats about all. :lol:

 

Good day

Floyd

ps: i also have a factory table attachment. It mounts fine and is totally useable. It came with a used machine purchase of mine.  With these respectfully,  I now understand the newer options available, they look Great! 

  • Members
Posted (edited)

Sometime it is better not to sell an item than to sell a crappy made item.

However - can you post pictures of the hole thing + machine? What kind of machine is it? I never have seen a foot lifter in this position on a cylinder machine :blink:

Edited by Constabulary

~ Keep "OLD CAST IRON" alive - it´s worth it ~

Machines in use: - Singer 111G156 - Singer 307G2 - Singer 29K71 - Singer 212G141 - Singer 45D91 - Singer 132K6 - Singer 108W20 - Singer 51WSV2 - Singer 143W2

  • Members
Posted

The knee lifter arm looks like it has a bit of adjustment left where it can slide further into it's clamp, will there be enough to clear the bolt?

I agree, however that it's a very poorly made item, particularly if it's supposed to be made for that machine.

Machines wot I have - Singer 51W59; Singer 331K4; Seiko STH-8BLD; Pfaff 335; CB4500.

Chinese shoe patcher; Singer 201K (old hand crank)

Posted

I would as Jimi said talk to the seller as from the photo's the flatbed attachment is of poor workmanship, looks like someone's first rough cut. Also I don't think the main table is the correct table for that machine as it looks as if the front of the base is slightly over hanging the edge. Overall it looks like someone had a regular flatbed K frame sewing table that they hacked out the middle and tried to reuse the scrap.  What machine is this, I think it is a clone of the Juki LS 1341.

kgg

Juki DNU - 1541S, Juki DU - 1181N, Singer 29K - 71(1949), Chinese Patcher (Tinkers Delight), Warlock TSC-441, Techsew 2750 Pro, Consew DCS-S4 Skiver

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.


×
×
  • Create New...