All Activity

you could solder/braze or whatever to join it and make it more secure

You can see on the bottom center that it's not joined in any way. Just bent into place. Easy to duplicate since it doesn't need or have any strength.

Welcome aboard. Whips interest me but by the time I look at the work and time involved, I just don't see myself going down that rabbit hole. Looking forward to your contributions.

I have to agree with you. Small spacing looks too busy.

I would use Neatsfoot oil and either wax or a couple of coats of Resolene 50/50

I did noticed but was so shocked at the so called repair. One thing that made me smile and wince at the same time was edge shaving the patch after it had already been stuck in place, was waiting for her to slip and damage the seat even more. About the use of tools I always say a mushroomed leather tool is a abused tool. Regards JCUK

Funny enough I had to replace some dressage billets last week the previous person who had done the, who I don't know not only machine stitched them way more than needed (not back stitched them) which led me to believe they were not sure of they were doing but also used a rivet too through the saddle webbing, never seen this before so before I started the repair I checked with the local tack shop who gave me the saddle if the owner wanted the rivets replaced too which they did, the webbing was still safe to use but I wanted a email saying the owner had said yes to the stitching and rivets before I started the repair. I meant to ask a the time of the previous thread concerning sliding reins by that do you mean draw reins. Regards JCUK The stitch used for saddle billets is called a back it gathers twice much of the webbing in one stitch. Regards JCUK

Hey all! I've got a customer that want's a radio strap that's basically raw veg tan leather like the one in the picture. My question is what's the best treatment to keep this looking nice? Just oil it or seal with something? Idea? Thanks Dean

I was. The spacing recommended by the designer was the smaller ones. I didn't like them as much, so tried the bigger ones. There are a few options with this template set, so I'm running through options, and trying to appreciate the design elements I would not have gotten right. I've seen those, but haven't had a chance to try one. They do add more bulk, but I like the design you used with it. Interesting choice on the screws, too.

It would take special tooling for the setter and anvil and I haven't seen that as a "stock item" It would take special tooling for the setter and anvil and I haven't seen that as a "stock item

there ya go!! Then I would coil a whole stick of it around a piece of hardwood or steel after annealing, then cut it down the side making dozens at once. Like they make chain mail.

Even I could make it. Anneal some brass rod, bend either free-hand or round a former then heat & squench

I wanna know how Chuck123 would make it!

These are two separate items; a grommet and a brass chain link. The grommets you can find pretty easily. The individual brass links are going to be harder to source. You can buy a brass chandelier chain and take off links as you need them. Make sure you get a good thickness so it doesn't pull apart.

Hi everyone, I’m excited to finally join this community after browsing for a while. I’ve been working with leather for a few years now, focusing mostly on hand-crafted bullwhips, biker gear, and other accessories. My main interest is combining traditional techniques with durable materials (like kangaroo leather) to create gear that’s both functional and long-lasting. At the end of the post, here are a couple of recent projects I’ve finished: I’m always looking to improve, so I’d love to hear your thoughts, critiques, or suggestions. It’s great to see such a knowledgeable group of leatherworkers sharing their craft here. If anyone’s interested in seeing more of my work, I’ve been building a small collection on my site: bantoro Looking forward to learning from you all and contributing where I can. Best regards, Bantoro Crafts

Hi there, thanks for answering! I’m just wondering where I could source this hardware? Also if you could provide the names of these pieces that great. I know one part is called an eyelet/gromet, but not sure what the long, oval ring would be formally named? Any help is appreciated. Kind regards.

you could make that in less time than it took you post this. Am I missing something?

Holy cow, you be careful, Its hard to heal up and no fun at all. I've finally finished working on the truck, i think. I found a leaking oil cooler hose and changed them out yesterday, friggin arthritis in my thumb makes it hell to start bolts and tighten stuff. Elk season is near, its an excellent meat, very lean and i rate it a close second to Antelope. The taste of wild meats is largely due to two things the fat and how you take care of the meat during the processing. Most of the gamey taste comes from the fat and the blood, so it's essential you take it all off during the butchering. Ageing of the meat is also very important. Just like ageing beef, i usually hang my critters for a week at least to drain all the blood and tenderize the meat. The meat also develops a hard rind that is trimmed off during the butchering and takes with it any dirt, hair or blue skin that may be left. My dad taught me some very old school ways that have been largely forgotten over the years, he was raised primarilly by his grandfather, who came here from Ireland, and his uncles, who were early settlers of this area. Plus he grew up in the 30s with no electricity lol, everyone did things this way. We never used refrigeration in the process we had a shed that we hung the critters in it was dark and well-ventilated every day dad would cover the critters with a linen sheet, then at night, uncover them so the cool air could get to them. This would keep the meat cool and dry, literally as long as you wanted it to hang without going bad. Taking the burb out for its test run after all the work today, the wife and i are going to dig some more clay, hopefully to last the winter and see how the colors are changing in the leaves.

Ohio Travel Bag is a name you may look at . . . I believe they are owned by Weaver Leather now May God bless, Dwight

Hi everyone, I am looking for this specific hardware to tether a chain to a trucker wallet. Anyone know any good sites for this type of hardware? Ideally in both solid brass and nickel options. Many thanks!

Yep. I normally don't laser cut, but I don't have a 1.25" hole punch. Honestly it was never intended to be finished.

Finally finished it, made a new handle/pivot, took me two goes to get the right length linkage but the beauty of this design is it's pretty easy to modify. It is much better to use with the handle like this. And please ignore the crappy welds, there's nothing wrong with the MIG, just the operator!

Hi I have recently purchased one of these Patent Elastic machines. Unfortunately I didn't realise the bobbin case and bobbin were missing. Is anyone able to suggest where I may get one from or does anyone have one they would be willing to sell? I would also like a copy of the manual mentioned earlier in this thread if that is ok? Many thanks in advance for any help that may be available. Regards Smileyface

Ya, I'll do it! Can't help myself

That does look great! I'm also restoring 2 of these machines. How do you do the paint? It looks absolutely original. Thanks!