All Activity

These are works of art, looks like you could use it to do pull-ups with. I'm impressed with the look more than the function

It's nice, in both art and gesture.

I see it now, too. Sort of a brown circle, midway of the shaft on the left. It's a tapered pin and I can't tell you which way. I'd also concur with leaving it in...

I don't know why, but I can't edit this ad to add pictures or anything. So, here they are.

Yes, lots of trends to follow, and with social media everyone's an expert.

great job!! A bit heavy leather, IMO, but hey, they look fantastic and should work well. I would suggest,using these clips made specifically for the job if you do any more of them. I have had the ones you used snag the thumbpiece and open just on my suspenders. https://www.ebay.com/itm/171369888626?var=0&mkevt=1&mkcid=1&mkrid=711-53200-19255-0&campid=5338590836&toolid=10044&loc_physical_ms=101688&customid=32c1eb99c2f11fb7b82f83561eeeacea I always liked the 3-point sling for tactical carry, and I use the M1907 rifle sling on all my long-range guns, so they all fit the same.

excellent work for a very worthy reason!! great job on the hair texture.

how about a screw extractor. not sure if it works but IMO it one of the last options you probably have. There are other model video show just a random one.

Hi Tove Welcome from the north-western part of Denmark. I am looking forward to seeing some of your creations here. Brgds Jonas

Hi All! First I just want to say how grateful I am for this forum. I've learned so much from you all. Thank you for sharing your knowledge and expertise! I just picked up my first compound feed machine, a Singer 111w155. It sews OK, but the outer presser feet don't lift up enough to accommodate thick material. Based on the manual (see pic attached), it seems that to adjust the relative height of the outer foot with respect to the inner (needle) foot, one has to use the lifting eccentric. However the set screw is stripped and very stuck. See the pic attached. I believe the stripped screw is "C" in the manual screenshot. I also noticed that screw "D" (which I think is the one people call the worm screw) spins freely, which seems weird. It appears someone may have ground away part of the machine casing to get better access to this screw in the past...can anyone confirm from the pic? So far I have tried: spraying the screw with PB blaster nightly for a few nights using a Dremel with a small pineapple burr to deepen the flathead groove gently tapping the screw with a screwdriver and hammer heating it lightly with a mini butane torch I got the screwdriver to bite better when I drilled out the groove, but when I applied force, it again started widening the screw groove again and eating away at the screw head. Can anyone offer other suggestions? I am considering taking it to a local machine shop to see if they can rescue me. I am hesitant to try a left hand drill bit and screw extractor, because the option of deepening the flathead groove further with the dremel seems like a good one and I don't want to burn that bridge. Help!! Am I missing something? Thanks! Matt

if it is not necessary to remove the shaft better leave it where it is. such actions sometime cause more damage on parts that most likely are no longer available. My 2 cents.

Looking a photo 1 again I see what appears to be a pin on the left, notice the circular dissimilar coloration on the shaft.

Plate 467, part# 15152 singer 27-1, 2, 3. 4 parts.pdf

I would have expected something like this, or a tapered pin in the same place.

It does look that way in the photo, but I've checked and those holes go all the way to the shaft. (A bit of lint in the bottom of the holes casting shadows). Are there parts manuals for these old machines? All I've seen is the user manual: https://ismacs.net/singer_sewing_machine_company/manuals/singer-model-27-number-2-vibrating-shuttle-sewing-machine-manual.pdf which does have somewhat of a drawing

Yeah, she was only 18 months old. Was fine one day and the next she was real lethargic and not herself. Ended up being kidney failure and they had no warning or signs there was a problem. It was only 3 days from noticing she wasn't well to having to put her down.

Practically everything is. Real EU made parts are EXPENSIVE. Chinese made parts are priced better. You get what you pay for though. Used price? 3500 and up.

Nicely done and a nice gesture !! Putting them is a hard thing .

@friquant In the first picture there appears to be screw slots inside the holes, maybe screws in there?

Thank You

How to remove the arm shaft from a Singer 27 ? Normally, I repair machines leaving them mostly assembled. To step outside of my comfort zone I decided to take one apart. I'm already dreaming of how clean I'll be able to get all the pieces ✨ But it's not clear to me how this arm shaft comes off. In the picture on the left, those two holes go all the way to the shaft. (Oil holes, I presume) 27-arm-shaft.mp4 There are few things inside that have to come loose also, but I'd like to get the arm shaft on its way out first: I think the arm shaft comes out the front of the machine. I removed the set screw just to the left of center in this photo: Inside the nose, with needle bar and presser bar removed: A couple interesting things about this machine, is it has a cam for the takeup lever, and a shuttle for the bobbin:

Artisan Toro 3000 heavy duty stitcher, 9" long cylinder bed, compound needle feed, walking foot, lockstitch sewing machine, complete with ArtisanESM-4002 Electronic DC Servo Motor, Sr-2 speed controller, EP adjustable pedestal, Lamp. extra needles, bobbins, bobbin winder, screw drivers, wrenches, oil and manual and work plate. Runs as good as the day I bought it.. Has been kept clean and oiled. Purchased new in 2005. Weighs 150 lbs, so it must be picked up. Located in Floresville, Texas. Price: $950.00 CASH

@KloverI found the thread where this was discussed. This link should take you to the page where the hammers are shown:

Thank you for the input! I'll definitely check out those images/videos. And thank you for mentioning the thread slippage. I hadn't even thought about that, but I will keep it in mind!