Bersa Thunder . 380 Inlay attempt

[tsunkasapa]

10 hours ago, Bert03241 said:

  what would be a good color?

I think I would go with either straight saddle tan, or dark brown. Perhaps cordovan. When I look at it my eyes should be drawn to the inlay, and they are not.

[chuck123wapati]

11 hours ago, Bert03241 said:

 

What I think I did wrong is the inlay is on top of the leather with a frame around it , not technically in layed. but I really didn't know how to do it on 8oz leather LOL  

I don't know if i do them right but here's how i do it. For an 8oz thickness holster for example i would use two pieces that equal 8 oz. One( the base layer thickest piece) under the snake skin, one over( the piece you cut out for the skin to show thru). and then i use the cutout piece also under the skin to raise it up level with the outer piece.  The outer piece should cover the whole holster so it looks inlayed.

[Bert03241]

2 hours ago, DwightT said:

I guess that technically makes it an "overlay" instead of an "inlay"?  It was hard to tell from the photographs, especially when I was looking at it from my phone.  Still looks pretty good to me.

    /dwight

Yea an overlay LOL glad you like it , thanks Dwight

[Bert03241]

1 hour ago, chuck123wapati said:

I don't know if i do them right but here's how i do it. For an 8oz thickness holster for example i would use two pieces that equal 8 oz. One( the base layer thickest piece) under the snake skin, one over( the piece you cut out for the skin to show thru). and then i use the cutout piece also under the skin to raise it up level with the outer piece.  The outer piece should cover the whole holster so it looks inlayed.

Thanks Chuck I'll give that a shot on the next one I do.

[Bert03241]

10 hours ago, Gezzer said:

Hey Bert , while I don't know about holsters  it looks pretty good to me. I think it would be even nicer to use a stitching iron or awl instead of drilling/punching your stitch lines .

yes I totally agree, but its seem every time I try that I mess up the stitch lines and ruin a piece leather. But I'll try again-the outside lines arn't to bad as I can use the groover or compass but the inside lines I have nothing to guide me and my free hand is awefull

[doubleh]

It looks pretty good but to my eye it would be better if your inlay followed the outer curves of the holster. Also it appears that you drilled the holes. Drilling is OK if you then run a stabbing awl thru the holes to make them diamond shaped. That is what I do with thick leather. It makes it much easier and and you can't tell the holes were drilled.

[Bert03241]

4 minutes ago, doubleh said:

It looks pretty good but to my eye it would be better if your inlay followed the outer curves of the holster. Also it appears that you drilled the holes. Drilling is OK if you then run a stabbing awl thru the holes to make them diamond shaped. That is what I do with thick leather. It makes it much easier and and you can't tell the holes were drilled.

Deciding how to shape the inlay was the hardest part

[Hags]

Use a smaller drill bit, then run the awl though.  Or, run a groove or line on the back and watch where the awl is coming out. As long as you don't pierce the leather, you can adjust. Then wet it and hammer it down. That shrinks the holes a bit as well. I tend to make my holsters a bit wider between the slots. It feels more comfortable for me as it spreads the load. I don't skive the back of the loops,  but do use a 1/4" x 1 1/2" (large paint stick)with rounded edges to slide in during the later part of wet molding to arc the holster and pull the ends down and in. Hope this helps, everyone is a bit different.

[bladegrinder]

I think it looks good but those stitch holes do stand out.

[Gezzer]

3 hours ago, Bert03241 said:

yes I totally agree, but its seem every time I try that I mess up the stitch lines and ruin a piece leather. But I'll try again-the outside lines arn't to bad as I can use the groover or compass but the inside lines I have nothing to guide me and my free hand is awefull

Maybe draw the inside lines on you  paper/card stock pattern where you can erase if needed .Once you like them  mark with a round awl as you trace your over all pattern . I have to get stuff right " on paper " all of the time but it saves me some leather .