All Activity

Alzilla, It would be nice to reset it to factory but I do not see it in the meanual. Where do you see it in the photos ? thank you

Weaver makes nice clicker dies as well. Reasonable priced too.

You don't need a proper leather working awl but could use one of these pokey-hole tools They can be bought cheaply. Put your leather over a plastic cutting board and push the pokey-hole tool through

See if there's an option to reset it to factory settings. One one of mine I recently noticed an option to hold down two buttons for so many seconds to reset the box. That's all I've got. EDIT: Actually there's an option for it right there at the top of the 2nd pic.

So, I turned on the machine today and I keep getting an error, Er 4, on my controller unit. THe machine won't run. I hav eto sew something for a show next weekend and am trying to find the fastest fix. If anyone can help I would appreciate it. I don't understand the manual. From the controller manual, E4 means the board needs to be replaced. But a few lines below it says E4 is the pedal. I get the message even if the pedal is not connected. Anyone knows what can be going on? I emailed and called the store but it is Saturday so no luck. Is a controller board supposed to fail so soon? Should I expect this to be replaced under warranty? I am not even sure what the warranty is on this machine.

Oh yeah, it'll be harder to sew. But it's fairly thin leather. You could pre-punch the holes with an awl

If you go to google . . . search video: concho belt you can watch videos for the next several hours May God bless, Dwight

Its not quite as bad as that....you can still have handguns if you are a member of a shooting club. Roger

Thank you both for your help. Will definitely give hotter water a try. I've only used plain tap water that was fairly cold. Will hotter water make it harder to sew? I'm only making about 4 pairs of holes near the fold so I'm just brute forcing a sewing needle through. Will I need to pre-punch the holes before using the hot water? The idea of giving my little duckies "armored" beaks is a hoot and will make for a great 'story' for them.

Good lookin work . . . but how in the world did you manage to hang on to a 1911 when your government played bad boy and burned all the guns??? May God bless, Dwight

I made a couple of knife sheaths for various knives.....a pancake for my work knife, an SOB for a tracker style knife I made and one for my old Mora... The pocket in the SOB carries a diamond sharpener, ferro rod and assorted bits and bobs... Roger

I also made made a Wild Bunch holster for my 1911 Gold Cup...my first attempt. Roger

Selling my Clicker 700 that was used for one project only (a couple hundred foam presses). It’s been sitting since, so I’m moving it along. Machine is fully functional and in excellent condition. Package: Clicker 700 press Matching stand C201H air compressor + hose (ready to run) Why this setup? Turn-key—connect power/air and go. Ideal for leather, foam, gaskets, and small-batch production. Clean, reliable, and barely broken in. Price New: $4,500 Asking Price: $1,900 OBO Location: St. Petersburg (Tampa Bay, FL). Local pickup preferred, but I can palletize for freight if you arrange shipping. PM for additional photos, a test video, or to come see it run. Facebook Marketplace Link for photos: https://www.facebook.com/share/175oYsma25/

I made some pouches for some mates in the Big Game Rifle Club..... I use girth elastic to hold the rounds, some are spaced for double rifles and the pic of the cases gives you an idea of the sizes... Roger

Thanks for that; gotta' track some of those down. Larry

Did you see the add at the top for Ohio Clicker Dies?

My boss likes to break needles off at the top. Took me a while to figure out the problem until I realized that the top of the broken needle was stuck inside of the needle holder not allowing the new needles to set correctly (too long). Check to be you don't have a broken needle inside the carrier.

Those are Chicago Screws the work out very nice.

Final offer $2500.

Selling my Clicker 700 that was used for one project only (a couple hundred foam presses). It’s been sitting since, so I’m moving it along. Machine is fully functional and in excellent condition. Package: Clicker 700 press Matching stand C201H air compressor + hose (ready to run) Why this setup? Turn-key—connect power/air and go. Ideal for leather, foam, gaskets, and small-batch production. Clean, reliable, and barely broken in. Price: $1,900 OBO Location: St. Petersburg (Tampa Bay, FL). Local pickup preferred, but I can palletize for freight if you arrange shipping. PM for additional photos, a test video, or to come see it run.

The feed mechanism is not really super great when it comes to thick stuff, so in addition to setting the adjustment on the back to H like @CowboyBob says, it also helps a lot to push/pull gently to help the object through. It also depends on how much pressure you keep on your presser foot, if it is pushing hard, and there is a lot of friction between the leather and the sewing machine, it can be hard to move just by the feed mechanism alone. I'd say 8 mm is a good figure, you can go a bit thicker, but not always with great success. In my view it is a fantastic machine, but again, my work is mainly repair job, and it is really great at that. Brgds Jonas

I need only a few, simple clicker dies. I would like to get dies made and sold by US companies. Where should I look for good quality dies at reasonable prices? Also looking for a 4-ton clicker press. Any suggestions? Nick

Alternate take: safety-clutch-adjust-animated.mp4

The safety clutch on my Singer 144W was tripping too easily, so I decided to investigate. Here's a video showing how to adjust the preload. safety-clutch-adjust-calm.mp4

Rather then you fiddling with a new machine be it a demo unit I would go bring back the machine to the seller and ask them why the 794 needles don't fit and have them correct the problem. kgg