All Activity

Actually I don't have any glue in the holster. The stitching is the only thing holding it together

The fleece needs to be replaced. I will have to take the skirts off to accomplish that, correct? That is the only reason I was going to take them off. But if I'm taking that far, figured I might as well make sure I get it really clean and conditioned while apart. If I understand what shank nails are, no. All the nails I have pulled thus far were smooth. Just thinking by looking at it and not having previous knowledge in saddle repairs, why can't I just get a tiny punch and punch the leather around the nail heads out and pull it up. Then fight getting the nails out. Or hammer them in as flat as possible. Re-nail in the same hole with a larger head nail, or beside these (if I couldn't get the nails out). It seems easier than trying not to rip this thin leather. Am I crazy?

Yes You can clean and condition a saddle without totally taking it apart. If that is the purpose then you are as far was you need to go in the front end. If you are taking apart totally, then to get these rigging nails off then first remove the screws. I always have better luck lifting the nails from under the leather with a heavy tack puller. Once you get them lifted a little then you can go on top of the leather to pull them the rest of the way out. Otherwise you can chew up the leather around them trying to get that first bite. Here are the two I like and now carry for sale. If they are ring shank nails, be ready to say bad words and all bets are off.

Well, it's good to see you again. Are you still doing leatherwork? Life does come at us fast. ~J

Thank you

Great advice, @Dwight Thanks!

This tack puller has worked well for me on English saddles. https://a.co/d/hplCLS2

At extremely low speeds the power of the motor is extremely low, so there is no point to engineer a motor that would be extremely powerful to overcome that. It's better to use a different gear ratio. In the production operators are skilled, and speeds are high. With a combination of needle positioner and other automatic controls low speeds are even less needed. Outside of repairing stuff and hobby users there is not much need for such motors, we should be lucky for that what we have :))))

You can add just one tiny thing to make the whole rig just a bit sharper looking. Whether you use rivets or chicago screws . . . put them thru the outside piece of the leather for attaching the little belt around the holster . Doing that will get rid of the unsightly screw heads and rivet heads on the back side of the holster. Not a serious critique . . . just one of those things that will separate sellers . . . especially if you are at a show or something . . . where others there are showing their wares. You can show that your holster is "cleaner" looking . . . which can result in an extra sale . . . and a slightly higher selling price. Also if you use a buckle . . . put a keeper on the little belt . . . or use a closed buckle . . . makes it look more realistic . . . and again . . . just one of those things that sets you apart from the run of the mill makers and sellers. Always remember that even the slightest "upscale" idea can push your wares out if front of the crowd. John Bianchi here in the states was the guy who perfected that idea. He could almost have designed a cardboard box to carry your gun in . . . and would have had 100 sales sight unseen. May God bless, Dwight

Years ago I never paid any attention . . . but the producer and / or director of Bonanza and a few others . . . must have been anti gun people. None of them carry even one extra bullet . . . blank belts all the way around. Didn't notice it until I got into holster making . . . then started watching . . . goofy if you ask me. May God bless, Dwight

Thanks for this I'll have to do more research on this. Just to be clear this is for keeping leather in a museum/conservation environment, not a working environment.

I actually watched a video of his to get started. I'll search his YouTube page for more that get into details.

Cooling, you can run a servo at very low speed (its just a motor), but you have to current limit so you don't over-heat it, and when you current limit, you lose torque. By requiring a minimum start speed, you assure that someone can't run at very low speeds for any length of time and destroy the motor. At that minimum speed, the cooling design parameters are met. (A stepper motor is designed to remain stopped with the current being sufficient to hold the designed load and not destroy itself, though many systems drop to a lower current when stopped, as you don't usually need the full current to hold the load when stopped. Many DC servo systems do the same when the load is stopped by current limiting. That is not necessary on a sewing machine and would be more expensive to implement.)

Don Gonzalez has a couple videos on breaking down a saddle and cleaning. He gets into a lot of detail and shows you the tools he uses, some he made himself. https://www.youtube.com/@DonGonzalesMaker/search?query=breaking down a saddle

I am deconstructing an old saddle of mine. First time, no help but what I get online. Are there tricks to removing the tiny nails that are in old thin leather without tearing it? Also, my saddle's skirts are sewn together. I was advised not to cut them loose and just take it apart together. Since I have never done this before, I don't know if I will be able to really clean and condition the leather unless I cut them loose. Any advise?

i haven't had a Matt Dillon rig since i was about 8 or 9 lol I still have my Fanner 50 but the holster is long gone. It sure sounds like a fun project. He shot someone every week so he needed a lot of bullets. I still watch the show and check out the holsters. Some of the bad guy holsters are pretty cool too.

Glad you were able to stop by. Seem a little slower on here than it was several years ago. Lots of sewing machine questions.

Very clean looking. Great job!

He probably needed all those bullets to help make him look more regular sized - He was nearly 6'7" tall!

I have had several industrial machines over the years, mostly Singers of various types (eg 166, 154 etc) a Pfaff and a Seiko, I've lifted them and moved them around while building/fitting tables and never had any trouble lifting them - and I'm not particularly strong. I've just about met my match with the CB4500, however!!! The arm through the gap, as Al suggested, has worked for me.

What do I want to make? No idea yet. I've watched many videos on how the die steel is shaped using bending tools/machines so figured I needed one. Me being me means I have to make one. The concept is simple enough it just needs three things - a means of applying sufficient force to bend it, (force applied to the end of the sliding tube by a lever/handle), a means of keeping everything square/vertical while bending it (hence the square tube to prevent any twisting of the die) and the right shaped dies to get the bends (right angles, curves etc). The shapes needed can be determined by watching the videos. Bear with me, hopefully at the end you will be able to appreciate the full extent of my genius - or realise that I just confirmed I'm an idjit with no idea!

Please look at the package that the needle came from and let us know the designation on the needle. For instance, a System 794 or 7x4 in Schmetz S Point, or a 4-sided Diamond, or 3-sided Tri point, or an LR or LL twisted wedge point. The first 3 give a straight stitch line, but with a different visual front to back length on top. The last two are made with a left or right twist on the tip of the needle. While the needles can lay the thread differently based on their geometry, the only ones that might try to push the leather sideways are the LL and LR slanted wedges. Personally, I avoid slanted needles. My preferred needles either have a diamond or tri point, or an S point, which is an inline slicing wedge. If you sew a stitch line with each of these two types, using the same stitch length and tensions, The S point stitches will appear closer together and submerged, compared to the diamond shape needles. Then, there's always System 7x3 round point needles that poke a round hole and are made to sew fabric and synthetics, and create a straight stitch line with good visual appearance between the ends of the stitches. Now that the needle geometry has been discussed, there is something mechanical that could cause the strip to move sideways as your sew. That is a misaligned or loose needle bar and inside foot mounting frame. Normally, this frame is installed with a minimum of sideways clearance to keep it sewing straight. If some impact knocks the frame alignment out, it may sew off the center line. Look to see if your machine has an L shaped bracket screwed on at the bottom of the moving frame that contains the needle and inside foot bars. If present, make sure it hasn't loosened or moved to the left and giving too much clearance to the moving frame, which might be called the "rock frame," or such.

Very interesting... love it!

I can't see your vision dikman. What is it that you want to make with your dies? I used to buy a pattern, precisely cut out the wooden core and using the pattern and the core Id bend it around the nails until it fitted.

This is my second 1911 holster.....lined / double leather, black strap to match gun, 12ga shell because this is a three gun match...12ga shotgun, 1911 45ACP, and 40 cal + lever gun. Roger