Stamping
Geometric tools, basketweave, 3D stamps and alphabet and number sets. Learn to make patterns to suit your style.
529 topics in this forum
-
- 1 follower
- 27 replies
- 29.1k views
Here is another way I lay out angled baskets. Actually this is the way I do most of them now, especially for strap work. It involves no templates, and the angles may be just a bit different for the same stamp than my template method. First off, I make a light horizontal impression to establish a stamp width mark in the corner. I exxagerated the impression a bit for illustration purposes. I set one leg on this mark, and the other end of the same leg on the base line. This is my first impression. I then use that angle, setting the next impression against the base line and lining up the leg with the previous impression. I stamp an entire horizontal row. I then line up th…
Last reply by OLDNSLOW, -
-
-
- 21 replies
- 18.7k views
I do a lot of this type border around inlays or to break up a large area of basket stamoping on round things like rope bags and rope cans. I put in the border I use on a lot of these too. I scribe my borders inside and out, and then stamp in the rope stamp impressions. I normally start on the outside for wider borders or tighter arcs. I think these cans have a 15" circle or so. I used that pattern to make this arc. I line up the first row of impressions with the legs just barely overlapping, They will overlap more as we work in. If you start on the inside of the arc, Murphy's law says your impressions will be too wide and not meet when you get to the outer row. Mu…
Last reply by ryankim3612, -
- 1 follower
- 8 replies
- 14k views
First of three little tutorials on how I lay out basket stamping. This first one is using a template to establish the angle. To make a template, I take a piece of firm scrap and lay out a base line. I stamp one row, then a row above leaving off one impression until I have a triangle. I marked the outline on the scrap of how I cut that triangle. Depending on your stamp and your personal amount of overlap, that exact angle can be different even with the same stamp. Next I took some rectangular scrap, cut in a border line and lightly beveled the inside cut. I took my template, layed the flat side on the cut line, and scribed the angle line in. Next step was stamping alt…
Last reply by bruce johnson, -
- 1 follower
- 56 replies
- 17.4k views
This is my first project using an alphabet set. I have been carving out my own freehand style lettering in the past on the few personalized projects I've made. The top of the leather shield needed to fit 14 letters with some spacing in between. Bottom section needs to fit various length last name on each shield. So I had to order a small 1/4" alphabet set for this Firefighter shield project. I designed the layout for this shield to be able to accommodate the top lettering the best.
Last reply by JerseyFirefighter, -
- 1 follower
- 56 replies
- 12.3k views
I'm in the process of getting everything together for a 2" wide oval stamp with an outer border to stamp oval leather disks that will be stitched into the interior of my bags. I'll be getting my stamp from grey ghost graphics. The company is Walden Bags and the motto is something like "simplicity, simplicity, simplicity" or "Simplicity Through Elegance" or "Elegant Simplicity." Perhaps in Latin. Not sure I want to include anything like this in the stamp at all, but just thought I'd throw it out there. I've had three ideas for the stamp: 1. WALDEN in caps, centered and a bold outline font. I'll post the exact font later. 2. WALDEN, as in #1 above, perhaps a bit …
Last reply by UKRay, -
- 3 followers
- 44 replies
- 5.8k views
I saw a guy on you-tube do this and it turns out pretty good if you are looking for a ribbon border or such .
Last reply by MarshalWill, -
- 1 follower
- 38 replies
- 22.7k views
I have ended up with a fair number of 3D stamps, and have really been struggling with getting them to imprint on leather. I have tried several different things - dry leather, cased leather, wet leather. Hammering it to death, hand-pressure, different hammers and different surfaces. Nothing seems to do it. I know I'm missing something! If anyone can point me to a decent 3D stamp instruction or help me along, I would REALLY appreciate it.
Last reply by Stan, -
Is it just me or is it really hard to get a clean pattern with Tandy tri weave stamps? No matter how hard i try it seems the tool itself prevents a good crisp design. I know there has to be a reason for the major difference in prices between tandy stamps and other makers. Is the difference worth the price? Any suggestions on a good Tri Weave?
Last reply by Rockoboy, -
- 34 replies
- 7.2k views
If you aren't aware of the different tolerances in Tandy letter stamps then your work will look as crappy as the poor tolerances. I started stamping the "T " to be followed by an "I " and you can really see the difference where the "I " stamped higher than the T. I turned the stamp around and it lined up much better with the T and you can see how much lower the second "I " is from the first. So if you aren't getting good results it could very well be the crappy tools being supplied by our suppliers and NOT you.
Last reply by Tree Reaper, -
- 3 followers
- 33 replies
- 4.9k views
Guys & gals who could I purchase a custom makers stamp from? Something I can set with a big maul? Preferably a stainless steel or brass constructed stamp. What does something like this cost? $100+ dollars? Any & all help will be greatly appreciated. Thanks.
Last reply by DieselTech,
