Wizcrafts

It might help if you added your location to your profile.

If you buy them, let us know how these erasers work out.

If you are a true novice to industrial sewing machines, especially leather sewing machines like the ones you've listed, stick to the 441 clones. They have a short learning curve and lots of fellow users to assist you over the humps. If you still think you want to get a Campbell Lockstitch machine, go to Yoakum Texas, book a motel room for a 5 day week, Go to Campbell Randall and take one on one instructions on the setup, threading, adjusting, oiling and operation of the machine. Don't leave town until you are certain you can change settings, stitch length, needles and awls, thread types and sizes and leather thicknesses and still get great results without calling anybody for help. And, learn how to lock the starting and ending stitches despite not having reverse. The Campbell Lockstitch uses a separate awl and needle. A different set is needed for each change in thread size. Feet, bobbins and accessories are costly. Few people on this forum own these machines and those who do are usually busy sewing harnesses and holsters all day. Even fewer industrial sewing machine dealers have any experience with these machines (which were designed during the late 1890s and early 1900s). In the end, the Campbell will produce a top and bottom stitch that most closely "resembles" a hand stitching awl result (e.g., Speedy Stitcher). It can sew through plywood and even pennies. But, if you are not in a position to take in-person lessons from the company, move along to a simpler machine. If you find a Campbell, or Randall, or Union Lockstitch machine for sale privately, only buy it if the seller offers to demonstrate the complete operation of the machine. A non-functional or totally unadjusted needle and awl machine can be costly and very time consuming to repair and bring into working order. FYI: The Juki 441 clones are now found in most successful leather makers' shops. They are half the price or less of needle and awl harness stitchers, easy to learn to operate and use relatively inexpensive needles. You can learn to operate one at home in a few days, just watching videos and reading our forum.

Make sure you buy leather point needles. I use Schmetz system 794, size 200 (US #25) with #277 thread.

Hey guys, I found a page full of presser feet made by Cowboysew-Hightex. Some are for the Juki 441 and its clones.

The Juki LU-1508NH is marketed as a moccasin sewing machine, by Juki. It can have a different rate of feed on top and bottom, to gather the soft leather or suede around the vamp. Contact a Juki dealer for more info. Adler also makes versions of their machines to gather the vamps on moccasins and properly sew the bottoms together.

Matt, Darren IS a sewing machine dealer in NSW Australia.

What can sometimes happen is that if the top tread twists too much, on its way to the top tension disks, it can actually move up and out of the primary tensioning area. It may even move to the top, yet appear to be in the disk when viewed from the normal operation angle. This would mean little or no top tension, resulting in all the top thread being pulled under the leather. The same thing would happen if the tension adjuster nut backed off the beehive tension spring on top. All you would have would be the bottom rotating disk and check spring to tension the top thread. A third variation would be the bobbin thread binding in the bobbin case. This could cause the top thread to be pulled to the bottom. But, I think you would notice if the bobbin thread was jammed before you started sewing. If it turns out that the top thread is not staying down near the center of the top disks, feed it through one hole and around and through another hole in the post thread guide on top of the machine. Make sure you feed the thread through the steel guide in front of the top tension disks. It will help if you loosen the screw on that loop guide and lower it until the foot lifter rod just misses it when you lift the feet with the foot lifter pedal.

Grommit; The machine you linked to will not sew much more than 2.5 mm of leather without difficulty. It is what's known as a domestic sewing machine. The reason is that it is built to sew cloth, using soft, thin cotton or polyester garment thread. The feed is bottom only, meaning that the layers will go out of alignment as you sew (unless they are glued or taped together first). The foot pressure spring will probably not hold down veg-tan leather that is 4mm thick. Have you read my topic about the type of sewing machine you need to sew leather? It is a sticky article among the others at the top of this forum's landing page. It will clear up any confusion you may have about the types of feed needed to properly move and hold down leather as you sew it. PS: If you happen to have or obtain a domestic sewing machine and need to sew garment or chap chrome tanned leather, buy either a roller equipped or Teflon, presser foot. These will help the top layer move with less drag.

Uwe; I don't think that CC stands for cracked case! More likely its for Consew Commercial.

I think Bob is referring to the screw sticking out of the barrel adjuster on the backside of the take-up lever. It wasn't there on any 29-4 I have owned. It came along in later generations and adds forced lift to the take-up.

Part of the problem is that the needle is one size too big for #207 thread. The recommended best size is #24/180, which pokes a smaller hole that provides the correct resistance for the knots. The take-up and tensioning systems in the 441 machines is not foolproof or totally perfect. The position of the knots can vary with changes in the bobbin tension, or in how the thread unwinds from the spool. Even fluctuations in the check spring tension can change the height of the knots. Troubleshoot this by checking the entire thread path. Then make sure the bobbin gives up its thread smoothly, without too little or too much tension. Change to a #24 needle, then balance the knots on the straightaways with the upper tensioner. Watch the check spring as the take-up lever moves up and down. It should keep the top thread taut until the needle just penetrates the top layer of leather. Finally, give the machine a full stroke on the hand lever. Partial stroking is a known cause of sewing problems in the Boss sewing machine.

Ken, call Bob Kovar, or a reputable industrial sewing machines dealer nearby, and get a price for a new Hirose 441 hook made to fit your brand of chassis that the Bull was built upon. It may or may not be the same part number as a Juki TSC-441 hook. The hook includes the bobbin case and spring.

I'll second that! The Family Sew motors are the best I've used, since switching from clutch motors. The front facing speed limiter dial is one of the most useful features, next to the removable cork brake.

Bob has been installing Family Sew motors on the 441 machines for about three years now. The last one I had with push buttons was in 2012. I had modified it with the light baffle tricks and it worked well. Then one day it quit. I've used the Family Sew motors ever since.

Pull out the shuttle and the spacer between it and the frame. Check for debris, clean the parts and reassemble them. Leave the race plate movable under spring pressure from the two screws. It should be possible to get more thread clearance doing this. If not, you may be right about the parts being added later on. I bought an expensive Juki hook for my CB4500 and it is too tight on the upstroke and causes the top thread to hang and snap violently. Maybe you can find an original shuttle and hook for your Consew Bull.

Ken; I don't know if your Bull is a clone of a Juki 441 or something else. If it is like a 441, the shuttle race cover has two spring loaded screws attaching it to the end of the arm. Loosen the screws between 1/2 and 1 full turn from finger tight. This lets the bobbin case and shuttle clear thicker thread.

Colt. I edited your links as best as I could with the options currently available under this new format.

Here is a needle and thread size chart from Toledo Industrial Sewing Machines. It shows the best needles to use with thread size 33 through 554. It includes the diameter of the bonded thread, tensile strength, plies, Govt equivalent sizes and Tex size equivalents.

Gosh! Does the servo on your Class 4 have a numeric LED display with up and down push buttons? If so, there is a setting (S something) that controls the direction it rotates in. I don't have any paperwork handy right now for these button options, but somebody else probably does. Leave the machine alone until we get these instructions for you.

Take a job as an apprentice sewer where Eric (Gottaknow) works. You will learn what you need to know to use the machine..That is that.

Bob, unless I misunderstood the problem, the slot feeding from the opening to the spring is too narrow. I assumed that Steve had him try to loosen the tension spring. I guess I should have asked that first. Maybe the tight spring is crimping the entry slot.

It's likely a bad part. Keep it for future use with #138 and smaller thread. In an emergency you can use Emory cloth or a file or thin grinding wheel to widen the slot. But, that will probably do more damage than good.

Maybe you guys should each start your own topic about these custom stamps. They can all go into the same section of the market place. It will make replies more understandable.

Are you rotating the handwheel towards you from the top-right? It needs to rotate counterclockwise to pick up the bobbin thread. Other causes include a needle bar than met resistance and moved up, throwing off the hook to eye of the needle timing. I don't know if your machine is equipped with a safety clutch that pops if there is a thread jam in the bobbin case, but if it is, the clutch may have disengaged the bobbin drive to protect the gears and hook. Finally, make sure that the needle is the correct system and that it is up all the way, and that the ribbed side faces left, while the cutout scarf faces due right.