Jump to content

Tree Reaper

Contributing Member
 View Profile  See their activity

  • Posts

    1,870

  • Joined

  • Last visited

 Content Type 

Everything posted by Tree Reaper

  1. Tree Reaper
    I just bought two from him, too small. Thanks just the same. Buckleguy on the left.
  2. Tree Reaper
    Anyone happen to know where I can purchase a 1 1/2 inch heel bar buckle in antique brass with a 5mm pin?
  3. Tree Reaper
    Tubular rivet Search: 20 results found for "tubular rivets*" (ohiotravelbag.com)
  4. Tree Reaper
    Solid Brass Clinching Nails (zackwhite.com)
  5. Tree Reaper
    Great information, thank you.
  6. Tree Reaper
    I've made contact with Service Thread, thanks for the information.
  7. Tree Reaper
    I have heard of VanNatta through Gerald Beranek (High Climbers and Timber Fallers). I have webbing slings and use them occasionally but my primary slings are loopie and whoopie made from Tenex. These straps were purchased new and still are but without eyes for reasons unknown to me. Without at least one eye they are pretty much useless, even as a tie down.
  8. Tree Reaper
    Now that's beneficial information, thank you. Let's not assume I'm using these for any critical applications. My working slings and ropes are the best . I was given these straps because they didn't have eyes, they could be used for securing brush or small trailer loads of lumber, hold a refrigerator to a hand cart among other things.
  9. Tree Reaper
    Just a loop on one or both ends. Found it, http://www.coatsindustrial.com/en/products-applications/industrial-threads/dabond
  10. Tree Reaper
    Dwight; The straps webbing strength is 10,000 but the working limit is 3300lbs. The strap is 1/16" thick by 2 " wide. These are not for resale but my own non critical personal use and I'm well aware of load limits. I'm just looking for the proper thread to use in my CB4500.
  11. Tree Reaper
    I want to stitch a 10,000 lb. cinch strap, what thread and where can I purchase this thread? Thanks.
  12. Tree Reaper
    Cut what you can and then sand it. Too much flesh left when they skinned it.
  13. Tree Reaper
    How do I get rid of it ?
  14. Tree Reaper

    How do I get rid of this column?

  15. Tree Reaper
    Thanks Ken.
  16. Tree Reaper
    How are you able to stitch this close to the high molded leather without the needle guide hitting the raised leather? Even with one foot the guide sticks out 1/4 of an inch.
  17. Tree Reaper
    Paint it with gold flaked paint.
  18. Tree Reaper
    I just finished the case I was working on.
  19. Tree Reaper
    Thanks for the explanation, I'm finishing one up myself and will post a picture here when I'm done.
  20. Tree Reaper
    It was formed and then stitched?
  21. Tree Reaper
    I can't tell from the pictures, how is the front attached to the back? Thanks.
  22. Tree Reaper
    Chris; You would normally wet the leather straps, stretch them leaving them stretched as they dry. How much stretch will be trial and error for the leather you have.
  23. Tree Reaper
    You could tumble them with a couple of balls in a dryer without heat .
  24. Tree Reaper
    I've tanned a few using supplies from Van Dyke, might be cabela's now. Get the grease off, tan them green if you can and break them over a round steel disk like a shovel .
  25. Tree Reaper
    I'm reluctant to think that this could be drilled out with any accuracy, specially if the pin is harder than the sleeve it's in. The problem I have is, these are already being made and are current production.
×
×
  • Create New...