All Activity
- Past hour
-
Ohio Travel Bag is a name you may look at . . . I believe they are owned by Weaver Leather now May God bless, Dwight
-
Hi everyone, I am looking for this specific hardware to tether a chain to a trucker wallet. Anyone know any good sites for this type of hardware? Ideally in both solid brass and nickel options. Many thanks!
- Today
-
Yep. I normally don't laser cut, but I don't have a 1.25" hole punch. Honestly it was never intended to be finished.
-
Finally finished it, made a new handle/pivot, took me two goes to get the right length linkage but the beauty of this design is it's pretty easy to modify. It is much better to use with the handle like this. And please ignore the crappy welds, there's nothing wrong with the MIG, just the operator!
-
Hi I have recently purchased one of these Patent Elastic machines. Unfortunately I didn't realise the bobbin case and bobbin were missing. Is anyone able to suggest where I may get one from or does anyone have one they would be willing to sell? I would also like a copy of the manual mentioned earlier in this thread if that is ok? Many thanks in advance for any help that may be available. Regards Smileyface
-
Ya, I'll do it! Can't help myself
-
That does look great! I'm also restoring 2 of these machines. How do you do the paint? It looks absolutely original. Thanks!
-
Can the pull the dot die work in weavers little wonder hand press?
-
I guess you mean the stitch length dial knob. I think I have a metal one here, I´ll check that later.... Or do you mean the Zig Zag knob?
-
CarolynGraber joined the community
-
Hear, hear! 🛠️
-
How about a close-up photo of the dial you are wanting to replace?
-
I did try to get the pin out...but the pin prevailed. Here is my "disassembly spread", inspired by @gottaknow's early post.
-
I've done that a time or 2 in the past. More often than not if it's a die or a punch in a cartridge that might stick I use a tiny bit of ballistol. It absorbs into most leathers without a residue or whatnot.
-
Smileyfaces joined the community
-
Post a photo. From what you describe, maybe a "strap wrench" of some sort?
-
A friend brought me tool that was found in a bunch of old harness parts. Brass head and handle like a hammer but has slots instead (about 1 1/4" wide and 1/4" or so tall) in either end of the head made like a strap would pass clear through. Ridges on bottom side of slot I figured for gripping and the hammer head is curved I thought for leverage. Anyone have any ideas what this tool might be?
- Yesterday
-
Help! Singer 111w155 stripped / stuck screw
AlZilla replied to matthew123's topic in Leather Sewing Machines
Just watch the banner ads for Toledo Industrial Sewing Machines and give him a call. Bob Kovar will know exactly what it is and probably have it in stock. Even if it's a standard thread and even if you know it, you won't know the length. -
Just an update if anyone is interested: I used the same size stitch holes (I'd already had two other bracelets pierced), and used the same size thread (277). Knot on the needle was coming loose: I pierced the thread with the needle and knotted it, and I had a much easier time keeping a tight knot on the needle during stitching. Stitches were loose: I waxed the bonded nylon thread (tied it to a shelf on one end and held it taught with my left hand and ran a wax stick over the thread length about a half-dozen to a dozen times back and forth, top and bottom), and I pulled each stitch much tighter than before. The stitching, even after bending, feels firm and set. Thank you for the help! (Oh, I realized the other night I had accidentally created a second account some years ago! Klover = Hydra.) 😅
-
Desert_Rat joined the community
-
josh76 joined the community
-
Help! Singer 111w155 stripped / stuck screw
DoogMeister replied to matthew123's topic in Leather Sewing Machines
Singer (made in USA) should be an SAE thread. Could be fine or coarse thread pitch. My local ACE hardware has a tremendous selection of screws, bolts, and such. Lowe's stocks stainless steel machine screws in size 4-40, 6-32, and 8-32. A hobby shop that caters to radio control enthusiasts will have small screws in both SAE and metric threads. Grainger, Fastenall, and McMaster-Carr also stock a wide variety of hardware. If you can identify the size and thread pitch, a gunsmith may be able to help. -
Baylee joined the community
-
ShinyHead joined the community
-
Adler K205 370 for sale $2200.00
adler sewing machine replied to adler sewing machine's topic in Used
-
Adler K205 370 for sale $2200.00
adler sewing machine replied to adler sewing machine's topic in Used
Houston Texas Shipping Via UPS PRICE WOULD VARY Depending on where your located -
Hi All! I am trying to bring a pfaff 138 back to life. The bakelite dial is cracked and I would love to replace it with a fresher, intact dial. I cannot find anything online. Any help to point me in the right direction is appreciated!
-
@Ciscokid noted on his profile page that the machine is sold. Locked/moved to Sold.
-
Model: 205-370 : Used Sewing 205-370 is a specialist for the manufacture of shoes and leather goods, saddlery, upholstery and technical textiles Cylinder Arm Single Needle Trip (Used) (Dusty but works well)
-
spring flowers and good food
Handstitched replied to chuck123wapati's topic in All About Us and Off Topic
I would love to try some elk on the bbq. I'm guessing it has a gamey flavour . I've had emu before, strong game flavour. Yep, bbq here I come 😋 had a bbq this arvo . Not too many peeps in the cities would take much notice of the changing seasons like us. I'm sporting a bit of a shiner on my right eye atm, climbing down from the back of my tractor I lost my footing and collided with the seat , hitting my face , just missed my glasses. I also went tits up in the paddock this arvo while spraying, anyone watching would have quite a giggle out of that. What a goose 🪿 😆 🤣 HS -
Birch tar based leatherconditioner and wax
Birchee replied to Birchee's topic in Miscellaneous/Other
As it is directly related I'll drop a article I just published on beeswax and its penetration on leather. https://birchees.ca/does-beeswax-penetrate-leather/