All Activity

They even match the paint job! 🤩 Does your machine have a piercer? That manual that Bob linked shows a piercer on page 22. I wondered what those are for..

Using a bandsaw blade should work BUT you'll have to anneal it first otherwise it will snap when you bend it. Once shaped it may need to be re-hardened, depending how stiff/soft it still is. Heating and quenching might warp the shape a bit and you would need to silver solder after re-hardening. Sharpening is a bit of a problem, so far I found the worn belt and a head magnifier the best as although it's slow I have better control. It may not work too well if I ever make a complicated shape.

Enviably straight pattern stamping, there. Mine usually wanders like The Ho Chi Minh Trail.

A lot of work but an interesting result. I'm all in favour of not wasting stuff where possible.

I have been making Salmon leather on and off for 4-5 years now, I always make it in very similar fashion as Russia leather was made. I believe I am the only one that makes Salmon leather in this way. The result is a very durable and wear resistant leather which is highly resistant to water, saltwater, molds, fungus, bacteria, and pests. After scraping and descaling the skins are soaked in a lime bath for 24 hours, followed by a vinegar bath for a few hours to bring the PH back to 5.5-6. They are then started in a 10:1 tea (inner bark of birch), tea is swapped out for full strength tea in small amounts as needed for seven days. They are then put in full strength tea for three days. Than they are partially dried and oiled either with mix of coconut oil and birch tar, or jojoba and birch tar, worked by hand until fully dry to keep them from stiffening up. They need to be hung for 3-4 weeks to allow the birch tar smell to mellow out. That smoky smell will persist for up to a year. This is the lime bath Bringing the PH back down in vinegar bath: Into the 10:1 birch tanning tea: Out of full strength tea and drying: Flesh side oiled and drying: Oiled and being worked until dry: Fully dried and oiled, hanging to air dry for a few weeks to let that smoky smell mellow out: Hope some of you find it interesting, a fair chunk of work but really enjoyable taking something that ends up in the garbage and making something useful from it. Oh and a bonus, me trying to tear it 😄

Hey, look. That guy in Toledo had the bed hinges. Thanks!

Started to get back into leatherwork after almost 10 years of on and off practice. I’ve made myself anything from holsters, belts, to knife sheaths. I still wear the first project I did 10 years ago around my waist (with a few new holes poked in it). A few of my rifles have been missing a sling for a while, So I decided that would be a good project to restart with. Not perfect, but certainly makes it easier to climb the Appalachian hills. ~9-12oz veg tan, some lined some not, no sewing machine, fiebings black dye, el cheapo amazon chicago screws, big box swivel attachments

Chrome tan - I wanted something with at least a 5 in the weight like 5/6. My overall favorite was anything with a shrunken grain since that tends to be heavier. Customers with no cost constraints - shrunken grain bison. I can't remember the exact cutting size. I gave all my templates and patterns for purses, bags, home decor, etc. to an up and comer years ago. Tooling leather - something with an 8 - 7/8 or 8/9 weights cut from lower side or mid belly-between the flanks remnants from those weights or split to 8 oz from skirting leftovers. They were 2 inch strips as I recall. Pretty sure I rarely cut many strips from a whole fresh side, just remnants mostly.

This is really well done! I like how you tapered each piece symmetrically. The tooling is great! Leaves on one side and wood chips on the other. Great attention to detail.

Nice...I use actual shell casings that I cut down...

Great way to save the project! Just the other day someone asked for a belt, when I ask for the belt size they said "about 30inches". I told them I couldn't make their belt if I dont have the correct measurement. I instructed them how to measure their current belt and it turned out to be 34". People are pretty vague when you're trying to get product info from them. What color do you want? Brown. What shade of brown? Like wood. What type of wood, like pine or mahogany? Yes

Hi everyone, I'm starting to think about a project that consists of sewing wool fabric (approx. 400gsm) with thick linen thread (diameter: 3mm). The aim is to use linen for decorative purposes but also to avoid synthetics. Given the thick diameter of the thread, I'm considering using an industrial leather machine. I have read quite a lot of advice by @Wizcrafts, particuarly on the following post: I would love your opinion on what you would recommend: Is an industrial machine (like the Singer 45K) recommended, or is it "too much"? My main challenge is finding a machine able to "accept" a 3mm or 4mm diameter thread, so I don't know if I should consider only heavy-duty leather machinery or if other options are possible. If the 45K or equivalent is too much, what "more gentle" option would you recommend? Would you recommend waxing the thread, specifically for sewing wool fabric? Many thanks for your advice, Clément

This was a different project for me. Ive always every to make a shooting bag just for the fun of it. I finally got around to it. I got creative in trying to make it appear aged. It was kind of nice not having to worry much about being perfect on a project. The rough edges and things add to the effect.

This post is informative of the consew t1919 performance envelope:

Bags are best done with a Cylinder arm machine while flt items like belts are best done with a Flatbed machine. A good all rounder to cover off round or roundish items and flat items would be a Cylinder arm machine like a brand name Juki LS-1341 or clone with a flatbed table attachment. There are quite a number of clone machines available at various price points. The thread V69 T70 is the largest thread your Domestic sewing machines typically can handle and pretty much the bottom end of what an industrial sewing machine can use. A Cylinder arm machine like the Juki LS-1341 (~$5000 USD) or clone ($2300 USD) can handle just over 3/8" thick leather which will cover off your projects. kgg

You'll need to get a proper walking foot machine, then get #18 leatherpoint needles in the "system" that machine uses. For instance, my Singer 111 and 211 machines take system 135x16 leather point, and 135x17 round point needles. I tend to hunt for titanium coated needles because I sew through leather tape or glue on a lot of jobs. Titanium coating helps prevent clogging of the eye of the needle. I also keep Goof Off and a dauber close by to clean the crap off the needles when they do get full of tape residue!

The disappointment and annoyance of suddenly having to deal with producing a product that doesn't live up to your own quality goals is exactly what is so hard to accept. Knowing that suddenly instead of a flawless product out there representing your skills, there is something completely different that you know ytou could have made better. The only good thing is that usually those who see it will still think it looks amazing, They don't know how it looked from the start, but it is still not much of a comfort to me.

Can I ask what thickness you use for the chrome tan & the veg tan? Any other tips you may have would be appreciated. Thanks, and again beautiful workmanship.

Very Nice..

It's something I think we all end up having to deal with at some point. I've had my share of "improvising" several things. It usually end up being a complete hassle, and disappointment because it wasn't part of the plan. Sometimes it'll look really nice and sometimes you wish you could just throw it in the fire pit. I hate improvising because it usually doesn't look like the quality I like to represent. Miscommunication is probably the biggest culprit. I know with belts, there's no standard to measure. Some makers measure one way while others measure it right...Oops I mean measure another way lol. Kids are the hardest because they're growing, and sometimes it's fast. I've only made a couple belts for kids. Not many people want to spend hundreds on a belt for a kid that's going to outgrow it. I add length so that holes can be added while they grow. And I know the belts I make will last a lifetime if not abused

While browsing Youtube for videos of English saddle construction, for some very strange reason this suggestion popped up. I speak very limited Spanish, so I can't make out what kind of straw that they use, and I think the saddle might be for the horse mounted person in a bullfight arena, but I am not sure. The interesting thing is that the saddle is built without a traditional tree. All the stiffness comes from straw. There is also some interesting decorations, that I guess are traditional. Definitely worth watching.

Use contact cement to glue the two pieces together. It will make everything stay together longer, and make stitching easier. I try not to have any "square" stitch lines. Ovalsare more appealing to the eye. On the sweat shield (back part where the grip rests) I wound trim back so that your hand can grip the grip without interference. You're off to a good start. Nice thing about leather, it lasts and ages well. Keep it up.

Ouch, having incomplete (or false) information to start out with is so frustrating. And I thjinbk you made a nice save! I promised my son to make a set of chaps for Christmas for his good friend (a farrier who does western riding). I was told that they should just be exactly like those that I had made for my son the year before, I asked if he really was the same size etc, and yup, just make them the same. Turns out that he would have liked his legs 4" longer.. I had to improvise to make it look decent, and I was pretty fed up with the project since redoing it was much more trouble than just making them correct the first time. But lesson learned 🙂

Just as an addition here. They do make a 45 acp rivet like the shotgun shell. I know it's got the 270 winchester rivets on Amazon, but i think the 45 acp was from weaver or tandy. You'll see it on this holster.

Hello, Thank you all for your feedback. Currently I make wallets, keychains, and coin purses which are all hand sewn. I primarily wanted to move to a sewing machine to hopefully expand my inventory with tote bags, belts, and other accessories. I work with 2-3oz leather currently but will need to go thicker for various projects. The thread that I attempted using was Thread # 69 T70.