All Activity

Those are Chicago Screws the work out very nice.

Final offer $2500.

Selling my Clicker 700 that was used for one project only (a couple hundred foam presses). It’s been sitting since, so I’m moving it along. Machine is fully functional and in excellent condition. Package: Clicker 700 press Matching stand C201H air compressor + hose (ready to run) Why this setup? Turn-key—connect power/air and go. Ideal for leather, foam, gaskets, and small-batch production. Clean, reliable, and barely broken in. Price: $1,900 OBO Location: St. Petersburg (Tampa Bay, FL). Local pickup preferred, but I can palletize for freight if you arrange shipping. PM for additional photos, a test video, or to come see it run.

The feed mechanism is not really super great when it comes to thick stuff, so in addition to setting the adjustment on the back to H like @CowboyBob says, it also helps a lot to push/pull gently to help the object through. It also depends on how much pressure you keep on your presser foot, if it is pushing hard, and there is a lot of friction between the leather and the sewing machine, it can be hard to move just by the feed mechanism alone. I'd say 8 mm is a good figure, you can go a bit thicker, but not always with great success. In my view it is a fantastic machine, but again, my work is mainly repair job, and it is really great at that. Brgds Jonas

I need only a few, simple clicker dies. I would like to get dies made and sold by US companies. Where should I look for good quality dies at reasonable prices? Also looking for a 4-ton clicker press. Any suggestions? Nick

Alternate take: safety-clutch-adjust-animated.mp4

The safety clutch on my Singer 144W was tripping too easily, so I decided to investigate. Here's a video showing how to adjust the preload. safety-clutch-adjust-calm.mp4

Rather then you fiddling with a new machine be it a demo unit I would go bring back the machine to the seller and ask them why the 794 needles don't fit and have them correct the problem. kgg

Thank you so much for the explanation. All the needles are the same length except the one that doesn't hit the bobbin cover. I backed the screw all the way out, and the long needles are still too long. Unfortunately, the needle that works best doesn't have a size designation on it. The thread I'm using is 346. I should add that I bought this machine from a well known seller of leather goods. They didn't have any in stock so they sold me the demonstration model. They, rather than Tippmann, might have supplied the oversized needles.

According to their manual Page 13 THREAD SPECIFICATIONS: Breaking down what "794s Serv 1 230 ...... SM 53-5 " means i) the 794s Serv 1 denotes the needle has a chisel point tip made for leather sewing ii) the 230 denotes the size of needle. Here is a good reference chart for the thread size vs the needle size needed ( https://www.tolindsewmach.com/thread-chart.html ) iii) the SM 53-5 is the Tippmann Boss part number for the needle. You can order these directly from Tippmann using their part number or from other vendors just by specing the needle system, needle size and shape of the tip of the needle. The needle system (794) denotes the length of the needle. All 794 will be the same length. Are all the needles the same length when you put them side by side?? It maybe as simple as you don't have the screw holding the needle backed off far enough. Otherwise I would call Tippmann. kgg

It does cuir bouilli, literally Boiled Leather, sometimes using a hot wax bath

I'll endorse Fred's answer. From experience, the hotter the water, the harder the end product will be. If you have plenty of leather, it might be worth experimenting with a range between hot tap water and boiling water. I think the hot water trick played/plays a role in making leather armor.

Only hot water from the tap, and not too hot at that Boiling hot water will really harden the leather but will make it shrink by as much as 20%, in uncontrolled directions

Lovely and so much detail on that paint job. Good to know that's an option. Thank you for all of your suggestions!

What kind of leather do you use for concho belts ? I have use veg tan. what kind of stain , condition and sealer do you use ? what are the steps ?

My Tippmann Boss came with a bunch of needles, but only one does not hit the bobbin cover. All but one appear to be too long. Looking to order in more of the correct size, I could see no size marked on the one that didn't strike the cover (unlike the other ones). In the chart in the manual the needle size given for the thread I'm using is "794s Serv 1 230 ...... SM 53-5". I don't understand what all of this means. Is 230 is the size of the eye? What indicates the length? Why did Tippmann supply needles that are too long? Is this a set-up problem? The machine works fine otherwise. thanks

Hot water out of the tap or boiling water? Love the vacuum seal idea too. If this works as well as I hope it does, that might make it much easier to do a bunch at a time.

Very nice. That Landis sure does the trick.

Unfortunately, the "W" series serial numbers aren't well documented. All we can tell is that it was made in 1943 or 1944. Meaning that it might have seen military service since everyone was pretty well focused on war time production. https://ismacs.net/singer_sewing_machine_company/serial-numbers/singer-w-series-serial-numbers.html

Good thoughts!! I'm gonna throw you folks a bone, suppressor cases !!!!! Be the first on your block and you're in.... there is a lot of good money in custom work and you can make a decent living but beginners arent gonna get it, plain and simple it takes much longer than a week to learn to make a decent "custom" holster for every gun out there in every style imaginable. A good many folks like to put thier multiple-thousand-dollar weapons in quality leather, but most of them that buy high-dollar guns know quality and they know leather holsters and they know beginners just cant cut it. I'll also add the best selling guns right now are really cheap and no one will pay 300 for a holster for a 250 dollar gun and why you sell 10 x more. So like you have shown its a bit more complicated issue than just waking up one day and saying "ima be a holster maker". Here in my town, the local gun store has a big box full of used leather they get on trade-ins for 5 bucks a pop. po folks buy them instead of anything new so another rock in the road to riches from holster making.

Good one, Northmount!

Looks like the shuttle race is not installed correctly,

hmm.

Being a moderator on a forum is a selfless task, often having to deal with all sorts of numpties! If that's indicative of Redhorses's attitude then I wish him bon voyage and good luck on whatever forum he goes to. Unfortunately for him this is the forum he really needs.

Dilute either the Future or Resolene 1:1 with water. Use several thinned coats, maybe 3. I prefer to use a version of 'Future' which I can get The paint won't help stiffen the leather Thin the paint and apply thin coats to build up the colour This knife scabbard was made in 2007, painted with acrylic model paints with no varnish to protect it. It was used regularly at events, tossed into a kit bag, generally neglected. It came back to me for repainting late 2016. After 10 years;