Stetson912

Before I start, I need to mention that this project deals with simple circuitry/wiring of a DC motor. Don't do this if you don't know how or understand the risks involved. With that said I made a burnisher for free! My neibor gave me two electric scooters that 'dont hold a charge' Soo, I gutted one. After taking it apart I realized that the motor for these scooters is a good little motor. It's a 24v permanent magnet motor that has a rated rpm of 2500-3000 with no load on the motor and ton of torque. Unfortunately the batteries were not good so no power for the motor.. or so I thought Wheels get to spinnin' and I realized I had a power supply to an old laptop... The charger outputs a 19v 4.78A dc current. I cut the end of the laptop charger off and wired it to the on off switch I salvaged from the scooter. Then wired the switch to the motor and viola! Burnisher motor with switch. I also recommend covering the connections with electrical tape or wire nuts or shrink wrap. In my case, I used hot glue, because it's what I had... Don't judge me! Hehe The motor works just fine. It's rated for 24v DC and at 19v (from the laptop charger) it runs fast enough for my needs. The actual burnisher is attached to the shaft by smashing a nut into a slightly small round hole. In the photos I repurposed a wooden drawer knob. I used a simple chisel to add another groove and also evened out the groove that was already there. So it has 2 grooves. All that's left is mounting it to something I can clamp down to the table. While it isn't the best thing in the world, it does work. It takes up minimal space, and is very light weight too. All in all, I'm happy with it. I'm posting this because I know people like me can't afford much. And sometimes you gotta make due. You don't need super fancy mega spinomatic 9000 burnisher models out there to get the job done (although if I could buy one I would) I hope this helps people out. Just remember to do your research and be careful with the wiring/soldering. I don't want people getting hurt or fried out there. The last picture is a burnish sample. It was done with just water and a little saddle soap and dried. No dye or wax or anything. It was a quick test so it isn't the best, just to show it works. Cheers and happy making!

Lol, I haven't tried mop n glo yet but people swear by it. I'll give it a try one day. I have used resolene over feibings before. It worked well enough lol

Resoline is acrylic based too. Idk why I never thought of acrylic paint as a resist until now haha. I've heard people using resolene for a resist in places. And it says right on the bottle "ACRYLIC" resolene hahaha. Guess I'm just a bit slow on the uptake aren't I haha.

It'll be nice when it ages. I like the blonde color of fresh veg tan, but something magical happens when it patinas and ages

@JD62 the company is called ks blade punch. They make hole punches and other tools as well as these irons. I think they have diamond chisels too but don't quote me on that. The unique benefit is that each tooth is made separately and inserted into the head of the tool individually. This allows you to polish and sharpen them (if need be) easier as well as replace any teeth that break or get damaged somehow. Obviously, a standard designed iron like the Blanchard's and such... Well they are very expensive and if you break a tooth you have to replace the entire tool. Not fun. Here's the website for is tool for further research... Or drooling... http://ksbladepunch.com/product/pricking-irons Also, Nigel Armitage's I believe reviewed the ks blade irons as well.

How do you like the ks blade irons? I'm looking for a good set. I like that the teeth are replaceable.

Just found buckle guy sells English bridle strips. Wickett and Craig, Hermann oak and Clayton's . Rough prices..Wickett and Craig is $13 Hermann oak is $17 and Clayton's is $27 all 8-10 some 10-12 oz 55"-60" length.

I still haven't seen this 'picture' of what my coworker wants. It sounds like it is an h style or step in harness. And I do have a pattern for an h style another member pmed me. She said it was a simple harness so, we will see.

I'm with you on that too @Mattsbagger which is why I'd like to get a bend or back or something. However... Since I can't reasonably charge that... Sadly hehe, strapping does sound like a great idea. Thanks for the suggestions.

You know, I have some veg tan light saddle skirting I totally forgot about. It's a total pita to work and cut but I have it. That's plenty strong for this right? I wouldn't think a harness for an Akita would damage easy made out of super stiff saddle skirting. Ah but bridle or latigo would be so much better. I wonder how much a bend from them runs? Might have to email em if it gets serious haha.

Yeah that's part of my problem. I just don't have the money for it. I don't sell much. So I don't have use for a large stock of leather. I don't feel right charging for the whole side or back or double shoulder. I can use lighter weight better than heavier weight too. I may just have to deny the job :/

Awesome. Here do you get your bridle?

I've unofficially been asked to make a coworker a dog harness for her Akita. I don't know what style she wants or have many details yet. I've never made a dog harness before so, as far as that's concerned I'd like to ask the more experienced on here what measurements I need and how to go about a pattern for it. As for the leather, I don't have anything suitable for a harness at the moment and will have to order it. I also can't afford to order a whole side or something just for this harness. I'm fairly certain just the cost of ordering the leather will put her off the prospect. But, in the chance she is willing to front cost, what do I use? I'm between English bridle and latigo. I've used neither of them but am a little familiar with their properties. Does anyone know a reasonably priced latigo or bridle leather? I saw the sipici brand on Maverick's website and am curious. Finally, I'd hate to have a heavy leather lying around and not be able to use it after this. Would a lighter weight leather laminated together for the harness straps be a good alternative? Believe me, if I had it my way I'd order a wickett and Craig side right now haha. Thanks in advance!

Nice!

Thanks @fredk. I forgot to mention skiving.

Oo cool. I like latigator...

Haha, that's cool. I imagine anything can be concealed if you want to

Oh, it's a concealed carry sw500 holster...

That could work

Yeah I hear ya. My brother in law wants an sob. I don't understand it myself. But everyone's different I guess. A cross draw for sw 500? Really? Sounds interesting

You already have eight. I think my model 94 holds 8 rounds (30-30). So that's one reload. You may be able to incorporate another 8 on a slider that can be put anywhere on the sling?

@garyplThat's awesome! Haha. You should do a cartridge belt or a slider even. I bet the sling comes out nice halitech.

Hahaha this is so crazy it's awesome. It's well made and I can't say I've ever known anyone to carry a desert eagle let alone two haha. Good work!

This is cool. One of my dream guns is the 1874 sharps in 45.70 govt.can you imagine a cover like that boasting those big ole shells? Haha.

You know what Jason... I'm starting to turn green here! Haha. Nice work as usual.