Jump to content

All Activity

This stream auto-updates

  1. Past hour
  2. jrdunn
    People are WAY harder to deal with than leather! JM2C, Jim
  3. Today
  4. WMages
    Looking to further tighten up details on leather holsters I build. I'm getting by currently with a round punch and a slightly too narrow oblong punch but would like to do this in one or two hammer blows. I normally build holsters matched with either a 1/4" or 5 1/16" belt. Could someone direct me to a good quality punch that will make the slots the size I need in one pass? I've looked at Osborns but haven't been able to determine the width of the slot they cut. I expect to pay a premium price so long as the punch is great quality. Thanks.
  5. jrdunn
    I think my AI radar is going off! This sounds more like an advertisement than a forum post. Maybe it's just me.
  6. PastorBob
    Agreed. I normally have them bring an old one to my shop or have them send pics of the belt with the tape measure on it. This would be good for modifying existing belts though. So far, I have only modified them to make it shorter, not longer. This would be a way to do it.
  7. kgg
    My take away is never ever trust someone else's measurements unless you get in writing and tell them if it is to short or long it's on them. Otherwise it is just too much wasted time / effort/ leather particularly something personalized or tooled should it go south. kgg
  8. LansingDrive
    @Tastech Thanks for that, yes that is a great machine and very much like the ones pictured in my comment. I am really interested to learn who created the design for that type of machine and when
  9. CowboyBob
    If you moved the hook to the left you "might" have too little clearance between the tab on the hook base & the cutout underneath the needle plate,you can either open up the cutout on the needle plate or move it slightly to the right.
  10. kgg
    I would go to your local hardware / auto store and see what they have. If the new one is to short / long exchange it for another. kgg
  11. kgg
    Just to add to this. @girlscout4 1. The needle has to be installed so the Groove (long channel on the shank) on the needle is to the left and the Scarf ( indentation / cutout ) on the right hand side as you look at it when sitting in front of the machine ready to sew. 2. You need to use a 135 x 16 x # needle for sewing leather. I think you maybe using a 135 x 17 x # needle which are made for fabric and will give you blowout on the underside. 3. You never said what size of thread and needle you are using. What size??? 4. A good thread to needle size chart can be found here ( https://www.tolindsewmach.com/thread-chart.html ) kgg
  12. kgg
    I don't think it will but that brings up the point is the needle bent or there is a lot of slop or a bend in the needle bar. Frankly I am surprised the hook is catching the top thread at all. The only thing I can figure is the top thread has so much slack the hook is somehow picking it up most times. kgg
  13. Handstitched
    Here in Oz , there's a TV program atm , ' Wheeler Dealers, where they buy unloved cars , fix them up, and sell them on. Tonight, they did an 80s ' Jeep Wagoneer' , ,it did remind me of your Suburban , it looked nice, when finished, but perhaps too nice,like brand new, but i would never take it to the places I've taken my landys , I'd scratch it, bend it to billy'o . HS
  14. WalterF

    Tobacco Pouch

    WalterF replied to WalterF's topic in Show Off!!

    Thank you, a food grade silicone. Thhank you, it can be frustrating. It is a food grade silicone, if I use a split zipper it may help. The challenge of something new keeps it interesting.
  15. Handstitched
    'I once saw a fish play a piano, it was a ' piano tuna ' HS
  16. ben27
    Hi all! I just registered on the forum. I have a Pfaff 145 and just bought a servo motor. The v belt that I had is now too long. it is an optibelt 10x1060. I tried measuring with a string and ended up with 97-99 cm inner diameter. Is there a way to keep using this belt? And if not, what belt do you recommend? Any people with experience with this clutch to servo swap? Thanks a lot!
  17. Mulesaw
    @dikman Ah, yes, that is a mistake from my side 🙂 In my head it was for powder, not the lead shots. I have never seen one of those before, so I thought it was for simultaneously filling powder in a double barrel muzzle loaded shotgun. But is the idea that you carry 2 sizes of shots? Or is it for a double barrel shotgun ? Brgds Jonas
  18. Gfei
    Gfei joined the community
  19. Samalan
    Beautiful job, Tim, as your work always is.
  20. Tastech
    Here is he previous post i was referring to . I am sure it is the same machine as this post mentions only a different brand name .
  21. Tastech
    I have seen the same machine with a different name. The machine in question i have seen was a Hugo Wertheim Melbourne . From my previous research i believe the machine was made under licence in melbourne. Hugo Werthiem also made smaller domestic machines and even piano's. Its been 5 years since i saw the machine and i really regret not buying it for $1200. If memory serves correct there was a recent post which has a picture of the Werthiem patcher .
  22. PastorBob
    Welcome from SW Missouri! Looks like you have been busy! Nice work!!
  23. PastorBob
    Great save! I haven't had to do that yet, but will file it away if I ever get the wrong measurement.
  24. chuck123wapati
    dope it up with Resolene or acrylic sealer, lol it'll be plenty stiff.
  25. AlZilla
    @kgg, well spotted! I wonder if turning the needle will better center it in the hole? I recently was playing with a domestic machine, having a problem shredding the top thread. Turned out the needle was off center and backwards, shredding the non groove side against the needle plate.
  26. kgg
    A couple of problems I found with your threading of the top thread. Without these corrected you will never get good stitching. 1. The needle is installed backwards. 2. Needle bar thread guide is missing. kgg
  27. Fonlandlaser

    Why Choose a CO2 Laser Cutting Machine?

    A CO2 laser cutter has become a reliable tool for workshops, woodworkers, artists, and makers. Known for its precision and versatility, it offers users a practical way to cut and engrave a wide variety of materials.

    Laser Cutter and Engraver

    The biggest advantage of a CO2 laser cutting machine lies in its versatility and cutting quality. It works with wood, acrylic, leather, textiles, paper, rubber, and more, delivering smooth edges and consistent results without the need for extra finishing. Users also value its long-term cost efficiency, as it requires less maintenance and has lower operating expenses compared to many other laser technologies.

    In addition, a CO2 laser cutter and engraver is easy to operate. Most models come with intuitive software that shortens the learning curve for beginners while supporting advanced needs for professionals. Whether you are creating custom signs, personalized engravings, or complex artistic designs, a CO2 laser cutting machine delivers precision, flexibility, and Versatility, a smart choice for anyone looking to performance and cost-effectiveness.

  28. Harry121
    Harry121 joined the community
  29. anselo
    anselo joined the community
  30. Origibelts
    @dikman Hi Dikman, Good question — you’re not missing anything obvious. The prong/tongue area where it pivots is what tends to give out first on a lot of buckles. That’s what DieselTech was flagging. I’ve been beefing up that joint in my castings so it holds up better under stress. Best, John
  1. Load more activity
×
×
  • Create New...