TomG

They hire unexperienced people and expect them to sell products they do not understand. This is all wel and good IF they allow the manager and other staff to train the people. And this would require crafting leather. It's a cost of doing business if you want to hire people who have no experience. It's up to the manager to control when they do this - during downtime I can understand them not wanting them to do "side job" stuff at work, but a blanket ban is ridiculous.

I'm in Tandy frequently and they've shown me their work. Maybe they did it at home and brought it in. I thought they did it there. I'll have e to ask next trip. But I agree. They should be allowed to tool leather. As long as the store and customer is not neglected. Ad that should be a manager call Tom

First, I believe you are talking about a side, not skin. Second, 18 sq ft is not a usable number. There will be unusable leather on that side. Too much fat, too many flaws, too much stretch, short pieces, etc. Third, if you're going to line them, you might want to use thick leather for the strap and thin or splits for the lining. Sounds like you are just doubling up. About the best you can hope for is to measure the side as if cut into a rectangle and hope you get to use 75% - 80% of it. It will vary by the actual piece

Yeah.. I'm not a prude by any means, but i don't think that's appropriate for this type of forum. And especially not on the main page. If it was a "biker" site, it might be expected, but I think most of the ladies.. and all of the kids.. don't need that.

I haven't seen the page(s) you are referring to. But, IMHO, skulls in the mix of leathercraft are fine with me. I've done them, but don't "focus" on them at all. But I agree with biker. We have an Adult section that questionable "art" and discussion belongs in. And honestly, I feel that you can be "adult" without all the profanity. What's that saying? Profanity is the sign of a small mind? Or something like that.. See. I just wrote 10+ sentences and not a single swear word !!!! Yea Me.. Bwhahahahahaha.

Has anyone used this to support soft leather when sewing bags? I saw it on a Leather Bag Tutorial I bought. It is supposed to stop stretching as you sew. I only found one place that carries it and shipping is more than the roll of tape. Any idea of if it's worth it or if there is a more readily available substitute? Thanks

Google "how to install a zipper" for more info than you can handle. Did you sew it in last? You usually want to sew the zipper in first and then sew the leather together with grain sides facing. Than turn it right-side out. That light leather should be sewable with a home machine and size 18 needles if you go slow.

Thanks. I kind of feared those would be the answers. I guess I'll just keep using my stainless strap to scrape them and maybe put a set on the other end for browns and such.

I have one of the Harbor Freight buffers. Great tool for cheap. I have stacked 2 or 3 of the firm pads to one side and mainly use it to buff straps that I have dip dyed black. It does a great job of removing the loose dyestuffs from the flesh and grain sides of the leather. After that, I finish with Black Leather Balm with Atom Wax and get virtually no ruboff.. After I buff, I use a piece of stainless strap and push the end of it into the wheel to try and knock the dyestuffs out of the wheel. I'd like to use it to buff other color straps, but not with those wheels, I think. Is there a way to clean them on the machine to use on other colors so I don't have to constantly swap out wheels? Thanks

Try this and scroll to the top

Even better, do a search here for Sandal Patterns. I seem to recall seeing a pretty good tutorial on making them a while back. I'll look as well.

Still.. the main point is that with a dog collar, the ring should have the leather going through it and then folded back around to hold it in place. Or a keeper strap riveted in place. Just like the keeper loop on a belt. And never, ever, ever put an economy, non-welded D-ring on a collar. Later

Easy fix. Put the collar through the D-ring and secure in place with a 1-1/2" long "tongue" using anything from glue to stove bolts. Doesn't matter if it breaks. It it breaks the collar in half, the animal has no business being on a leash!!!

I've used Tandy double-cap brass and nickle plated rivets for 10 years. I've had very, very few problems with them and 99% of those were me. 1/8" is too tall. 90% of the time, the post is going to lean or shift to the side. Especially if the hole is too large. The hole should be just big enough to let the cap set all the way down. 1/16" is the recommended height for all rapid and double cap rivets to the best of my knowledge. To use a "too long" rivet, I use a pair of fine, flush-cutting cutters to trim them to size once put into the leather and then reshape the post with them as well. I've had maybe 5 failures in those 10 years that I am aware of. I've also set them with and without the concave base. I've never seen any difference other than visual - flat base vs domed base. All of this being said, I recently bought the Goldstar press and dies. I have set countless double caps that were at least 1/8th" above the surface and had zero posts leaning over. I leave the dies in all the time and just grab it, set it on the bench and go. Just be aware that the Goldstar double cap dies are marked in mm size and Tandy rivets are all mis-sized. I beleive the mediums are marked as 7mm and are actually 8mm. So you have to buy a die size larger. Their Line 20 snap dies are not cut to fit the Tandy snaps either. They fit everybody else's, per the guy at the store. Good luck

If you just want a table to cut sides, get one of those 6 foot folding tables from Sam's or Home Depot/Lowes. Under $100 and folds up for storage when not in use. But don't use it for pounding. Too much bounce..

Yup. It's a 135x16 leather needle. I'm getting ready to sew another batch of these and just spent over an hour adjusting tensions, presser foot pressures, etc. Looks like I have it as good as I'm going to get it... Not absolutely perfect, but I don't think it's possible to get the bottom to look like the top <g>... my definition of perfect...

Thanks Mongo. My main problem was the amount of text in the area allowed. It's a moot point now. He just told me he found a biker shop that can do it with hot press. Thanks for the help, all.

Thanks for the suggestion. That was one of the options I mentioned to him as a possibility, but really didn't know if they can print so small. I also mentioned typeset lettering that can be filled in with paint....

I have a customer who wants a black patch 2" x 3.25" with the following on it. _________________________________________________ LTJG JIM DICKSON USS TICONDEROGA (CVA – 14) _________________________________________________ The only issue I have is that he wants the letters in gold or bronze. I have nothing this small that will fit and still be able to be colored. An suggestions? Thanks

Ditto on JLS's recommendation. Great folks to work with. I recently had a request to match thread and leather color. I sent them a sample of the leather and although they did not have an exact match (no surprise there), the recommendation was actually as near perfect as I could expect. One interesting thing I found out is that not all colors come in all sized spools. I have always tried to buy 4 oz or smaller spools until I see if I will be using that particular color. then I buy the 16 oz spools. That's a LOT of thread unless you as sewing every day, all day... If you want something closer to home, try a major sewing machine store. Here in Atlanta, we have Southeast Sewing. Great folks as well. They sell and repair industrial/commercial machine so they carry a nice selection of Fil-Tec threads

Hi Olie, I'm not sure how you came up with that figure. You didn't say what size belts, but figuring a 1-1/2", 72" long strap, is 108 sq in. (72*1.5). Divide that by 144 to convert to sq ft and it is .75 sq ft. At $8.20 sq ft, that is $6.15 ea. Tandy has 1-1/2" x 72" straps for $24.50 ea - wholesale pricing. Which seems a whole lot high to me. They have some precut belt blanks with snaps for around $15

Thanks Ferg. I did the sliding needle trick. The 21 had a little bit of snag as it went down, but that may have been me lifting the thread too high, come to think of it... I'll tighten setting up tomorrow and try again. And Wiz.. Yes.. Please jump in <g>...

Still learning the new Consew 227R and loving it. Have a question about the "quality" of my bottom stitches. The photos are 2 pieces of 7/8, glued together, 138 nylon thread top and bottom, both fee set to as light a pressure as I can get to avoid marks, but there is no lifting that I can see. Size 22 leather point needle. Longest stitch length the machine can be set for. Is there any way to improve the look of those bottom stitches, or is this just how it is? Thanks

Looking forward to seeing them!