kgg

Which features? kgg

It comes down to dollars and cents. Cheaper to replace non spec equipment IF the end user (us the customer) complains. I would think with mash production, probably in China, the manufacturer probably does spot checks on first tear client equipment and expects the client to be responsible for any further checks on the rest. kgg

I looked at your video, clearly shows no load startup at a couple of low settings. I would forward it on to Techsew to show them what you are contending with. The motor might have gotten a bang during shipment. I know I would definitely not be satisfied with that motors functionally or confidence in it's longevity. kgg

Nice idea, multi purpose guide. kgg

hi KennethM Have you tried removing the drive belt and seeing what happens with the motor having no startup load of the belt or machine? Or remove the feet from the machine all together and see what happens. Keep us up to date. kgg

I would with no question purchase a new machine with similar capabilities to the Ferdco unless the price of the Ferdco wasn't substantially lower then a new machine. I would be thinking of warranty and the availability of support, parts, accessories and repairs. kgg

Explain to the people what you are planning on sewing mostly from the thinnest to the thickest material. Remember there is no one machine for everything that is why a lot of people have more then one machine. I would also look at the following video's by Sewing Gold as they give a good comparison between the Juki ddl 8700 (taylor machine) the du 1181n walking foot and the dnu-1541s (unison feed) all sewing the same light, medium and heavy fabrics. The Juki dnu 1508 (unison feed) will be supposedly a little heavier duty then the 1541s with a double thread adjustment. They have good sound and video as a future comparison reference. kgg Juki ddl-8700 Juki DU-1181N Juki DNU-1541S

Did you buy the machine directly from Techsew or a dealer? Did the feet stick before you replaced them with the smooth feet? Once you check the links place the original ones back on and see if still happens. The new ones may need to be adjusted or filed a bit to give more side clearance. As far as the motor goes: 1. I would check the voltage at that plug anyway like Wiz said. If possible, plug it into another plug on a different circuit. 2. Remove the belt from the motor so there is no load on the motor during startup and see if you get a high rpm jump. 3. Check and see if the connection from the sewing table foot peddle to the motor level is adjusted properly and see if there is anything jamming the motors actuating rod or something got buckled during shipment. If you are getting smooth no load control you maybe having other internal issues related to the sewing machine itself that are causing an initial high load condition on the motor. As far as "needing more juice" unless you are having problems with other appliances / computers, lights constantly dimming or the machine is plugged into a circuit with high motor loads like fridges or deep freezes, I doubt a "juice" problem. Will that be orange or tomato juice with your veg? I am guessing that you have a bum motor. kgg

First I would call Techsew and explain your problems to them (no maintenance manual, sticky foot lift and servo motor high starting rpm). The info on their website says the 1460 comes with a their 550 watt servo motor with 12 settings between 0 and 3450 rpm. In the interim I would remove the front cover and see if there is something obviously loose or broken. If nothing is obvious oil the hell out of everything also check the foot lifting mechanism as well as the knee lift links. kgg

First Juki is what all the clones are being copied after these days regardless of who's badge is on the machine. I could be wrong but the last info I had was the Juki 1541's were the only ones now being made in Japan and the rest in China. Since this is going to be a large outlay of cash I would suggest visiting a Juki dealer with a sample of material and see what results their machines can offer then go to Toledo Sewing with the same sample and compare or vice versa. Compare the sewing results, the sound of the machines (does one sound rough in comparison to the other), balance of the machine (vibrations), speed control, availability of accessories and most importantly dealer support. Dealer support before and after the sale plays a very important part in the purchase of a new machine. Having a dealer relatively close, willing and able to tune your machine to your needs can be invaluable. Then you can make a educated decision as to which machine will be the best for you and your money. Since I am in Canada, I have not tried or seen any of the machines like the Cobras, Cowboys, Artisans and others which are common amongst a lot of the US members but have fine reputations for their machines and support. When I compared a couple of clone machines against the Juki machines up here there was no comparison they sounded like a bucket of bolts banging around in comparison and just as if not more expensive. I purchased the Juki 1541s for my needs. I figured Buy once, Cry once. My two cents worth, kgg

I would do as R8R suggested and if you are still a little unsure about something repost what you are trying to do and the problem you are having. Pictures / video can be very helpful. This way the problem could be narrowed down to the root cause and suggestions can be given. kgg

Remember to ask your customer if he has the 7, 8 or the 9 round versions of the clips or he has all three versions. The basic frame is the same unless he has added different front /rear sights to the slide, a bottom laser dot or different hand grips. The clips are three different lengths and this may play in your design / layout / making of the holster. Maybe worth checking what mods if any he has done to it as a standard dummy may or may not work. kgg

I have a couple of questions. What thread and needle combination are you using as well as bobbin thread size. What type and thickness of leather? I am going to assume that you have checked the amount of tension that the foot places on the material isn't too great; bobbin and main thread tensions aren't too great; needle installed in the correct direction, fully and clamped tight; bobbin installed correctly to allow thread to unwind properly. I think the 563 uses the same needles as my 1541s which are 135 x 17 but for leather work you need 135 x 16. I have bent a few needles trying to go through to thick of material even though it was the correct needle for the thread and material. My solution was to go up one needle size to get a little thicker shaft. I also use Schmetz sewing machine needles which I think are a pretty good quality needle and change my needle after 8 hours of use.

The way I read the manuals is the small level is a thumb nut that you move to regulate the stitch length only. The easy way to check is to place some material under the foot, slacken the thumb nut and then push it all the way to the top. Then turn the wheel towards yourself. If the material moves away from you it is just sewing then move the thumb nut to the very bottom, if the material again moves away from you then it doesn't have reverse and the thumb nut / level is just for stitch length. kgg

You mentioned you removed the clutch (stop motion ring) and cleaned it. I have two other suggestions to add that you may also check. Is the screw in the knob screwed in far enough to only allow the small knob of the wheel to have movement between two of the three exterior tabs on the stop motion ring (clutch ring) and are the interior taps facing the knob not the machine. If the screw isn't in far enough the exterior tab of the clutch ring could ride over it and if the inter taps of the clutch ring are facing towards the machine it will spin as soon as there is enough needle / material resistance. kgg

Hi Mocivnik, The price is right but how much is shipping / import taxes going to cost? If you are mechanically inclined and don't mind waiting for parts should something need to be replaced maybe a good deal. I would still advise you to see if you could find a good second hand cylinder bed machine that you would have easier access to parts and accessories. kgg

The Sailrite Fabricator is a flat bed versus the Cowboy and Cobra are cylinder machines which can be made into flat bed machine with a table top accessory. If you need the punching power because of the thickness / type of the leather and need 138 thread regularly. Go with a Cowboy or Cobra then add a table top. If you are using mostly thinner / softer leather or other materials and maxing out on 138 thread then look at the Juki 1541s and then get a used cylinder machine for the occasional need. I looked at a lot of Juki clones and figured that since most of my stuff falls into the maxing out on 138 thread and this would be my main machine I would cry once, buy once. I purchased the best I could afford, a new Juki 1541s and now I am waiting for the right priced (cheap) well loved cylinder machine to come along for the occasional need. The Juki 1541s with a Kobe 550 watt servo motor is a nice little machine. It creeps along as slow as I want through the max material I can fit under the foot and I have even forced material under the foot without any hand spinning the belt wheel, machine baulking, struggle or speed jerking from the start in both straight runs or curves. I am pleased and sometimes impressed with the Juki. kgg

I came across some 50 spools of Coates Dabond V69 white thread a couple of months back. The spools are the 1 lb size. I only need a few spools for myself but had to buy the lot. They are still individually wrapped in the original clear plastic. The description on the inside bottom of the spools is Coates V69 DABOND Bonded Polyester VT285F TY2 Cl-1SZ-E WHITE SVDP5737775. I have gone through about a spool so far with no problems. Price $5.00 a spool Canadian plus shipping. I am located in Toledo, Ontario, Canada.

dikman, I do agree that if my mix should drip down it will show a dark stain which is not what you want to see but then again I have accidentally over oiled with the regular sewing machine oil and have had staining occur. To help prevent any dripping from messing the needle / needle plate area I usually put a thick fluffy terry pad down and fully lower the needle into it. Why I like the oil filler for fly reels is that no oil is dispensed until you depress the needle against a part so not as much over oiling can occur. That said I do like your idea of the inkjet refillers and I must see if I have one around and give it a try. Another thing I have used for oiling is a syringe with a small gauge needle just don't prick yourself. I will remember your info about the hydraulic oil vs Lily White. kgg

I don't have seized up parts or heating problems but when rebuilding old Singers and I do appreciate the old Singers that I salvaged like Singer 127's and 128's from the early 1900's often they have had many parts initially seized solid. With some parts being difficult to get I have been fairly successful in trying to save everything I can. From the heat point of view in my other hobby, target shooting, parts heating up can be a real nasty problem with operation (jams, miss fires, parts fracturing to name a few) and accuracy of a lot of parts when under fairly heavy pressure stresses. The object is to ensure parts that rub /slide together or otherwise are exposed to these stresses have the necessary areas oiled with the best (slipperiest) lube possible as heat can be extreme and instantaneous. Particularly when shooting the larger cals. For my equipment I am willing to take the risk of voiding the warranty, broken parts etc. is that if the oil mix combination I use can withstand the rigours (heat / friction stress) of shooting it should be able to keep the parts lubed and handle the friction of most parts in most sewing machines. kgg

On my older sewing machines that I have had what I found to work really good for freeing up seized parts and regular oiling is a formula that we use on our guns. The red neck formula that we use is 7cc's of Royal Purple Synthetic Oil SAE 5W-20 for gas engines and 5 cc's of Motormaster Full Synthetic Dexron- VI Automatic Transmission Fluid mixed together. This has worked really good for parts that are exposed to high heat like slides. I am using this now on the daily oil spots on my Juki 1541S rather then the Juki oil but still using the Juki oil in the reserve for now. As a side note a great cheap refillable oiler that can get into those hard to reach areas without making a mess are oilers made for lubing fishing reels at 10 bucks versus the oiler for guns at 20 bucks both look the same. Just dump the oil that comes with them and load up with whatever good stuff you use. What do you use for oil and oilers on your machines. kgg

Welcome to the forum bassplayer. The vibrations could be as simple as the table missing the rubber feet, table needs to be leveled, table bolts need to be re tightened, the motor may need it's mounting bolts re tightened, wrong drive belt, worn or bumpy drive belt. I will let others give information on your other questions. kgg

Even though I do not own a Cowboy, if you really needed that attachment for your projects, you would pay twice the price for quality. I can definitely see where the cost of a proper binder for that machine is. For one there is a very limited number of people that would ever need one, design engineering, manufacturing, stocking and shipping. Hell I paid $80 for my 1 3/4" swing away plain tape binder and another $80 for 2 1/2" double fold binder for a Juki. Could have got something "similar" off ebay for about $15 each would have it worked, probably. Same quality or longevity, probably not. Most times you get what you pay for. Buy once, cry once. kgg

Now it sounds like you have a game plan. Best of luck, kgg

If you decide on the Juki 1541 or one of the clone equivalents get the Juki 1541S. The "S" stays for safety mechanism so if you overload or jam up the machine it disengages itself and is easily reset after clearing the fault by the push of a button on the bed. The cost differences between both models is only about $100, cheap insurance against buckled internal parts. Before purchasing a 1541 clone make sure you test it first then try the Juki. If dollars are not going to be the major factor I think you will lean towards the Juki on sound, feel, finish, availability of accessories / parts and reputation. It definitely will not sound like a bucket of bolts banging around fresh out of the box like some of the cheap clones. kgg