shoepatcher

The 335 can sew #138 thread. You just have to make a few modifications. Enlarge hole in inner foot and feed dog. Pfaff made a heavier take up spring. I would install that as well. I also went to work on the gap and finger on the bobbin area to have more clearance for the thread to clear on each stitch. glenn

Nice find C!!! glenn

Y The speed reducer screws with the sensing in the synchronizer. You can use a servo motor, synchronizer and speed reducer but not all three. I would get rid of the speed reducer. glenn

I would have the piece in the back welded first to see if it will work. Strima in Poland carries a lot of older parts. Check with them since you already have the part numbers. I you contact Pfaff in Germany and see what they have. There is also a guy on eBay in Lithuania that sells a lot of older Pfaff parts. glenn

call Bob Kovar at Toledo Sewing and see if he has any Champion parts. Use to work on them. glenn

take a video of the machine slowly sewing so we can see how it is jamming up. glenn

the 4 class is the precursor to the 104. great machines. I would not part it out. get it set up and running. glenn

Need to know exact model of your 268 to answer that question. glenn

Bradbury built from 1872-1923. Built in England. Smallest arm of any shoepatcher. Were great machines. I have manual on the machine. Closest needle system to Bradbury needle was Singer 175 x 5,7. glenn

HOW heavy a thread are you using. Stick with #138 and below. Will sew #207 on top but #138 is better top and bottom. glenn

see www.brunoanichini.it The 29K19 uses all the same parts as the 29K 1 except it had a different needle bar. glenn

what model you got?

767 manual will work as well. was used in auto industries. Looks like you have a Efka computer motor. That has all the functions. You have a 720 top control panel as well. That color machine made in the late 1980's. glenn

30-10 or 30-70? which? you must first check the needle bar to make sure it is at the correct height. 30-1 different than 30-70! One determined that needle bar is times, you then remove shuttle from the shuttle carrier to time the hook. There is an eccentric on the lower drive rack that you move to time shuttle carrier. I might be able to walk you thru it over the phone. glenn

That looks like a Juki 562 which was a copy of a 111 w155 with reverse. Goldsworthy was the the Pfaff dealer in Ontario until they went out of business about 10 plus years ago. glenn

Nice job on the rebuild. glenn

Paint in good shape. leave it. glenn

Weaver 205 clone an option. I have sewn on one. 90% as good as the original. I have a genuine 205 with toys. 969 Pure is a great machine. You buy the best you only cry once! glenn

The Adler 120-7A, 8A had a 40mm lift on it Could sew heavier than Randall Campbell and 969 DA. That was an absolute beast. glenn

From the color of the machine, it was made in the early 1980's to late 1980's. I had a Pfaff 1245 that color. glenn

The flat screw on the other end of the shaft that has the wing nut for adjusting the walk is off. That has to be loosened. I always replace that screw with an Allen screw 1/2" x 24tpi. Easier to adjust and you can tighten it down more on the shaft. Once loose, set walk with wing nut to lowest walk and slightly tighten straight slot screw to get the walk adjusted. Next go to highest walk with the wing nut. (letter H on the gauge) and adjust it so foot just comes up under needle clamp. You will get the knack of it with a little practice. glenn

Is Graham Forsythe still involved with it? glenn

No I would say 1999-2000 was first year. glenn

Located where? glenn