Search the Community
Showing results for tags 'servo'.
-
Hello, I’m a new member from Doncaster, UK, and I hope you can help me with a questions. I’ve recently acquired a Juki LS-341 with a TH-750S servo upgrade, and I’m looking to make a couple of modifications. LED Light Pl...
-
I just purchased an Adler K269-373 head only. I have a table on order but need a servo motor. This is my first industrial machine so I'd welcome any input on how to choose the proper servo motor or which brand/model might be best. I've budgeted something under $300 for this component. Tell me if I c... -
I have a 29K without the professional sewing table, looking to fit a table top motor to drive it, but what do you use for a foot controller, are there flexible ones like domestic machines that will operate the servo or do you have to make a mechanical one to use the servo imk. For a normal industria...
-
Hello! I purchased a leather sewing machine about 4 years ago and it came with a brand new COBRA TN-400 servo motor. I haven't used the machine basically since i purchased it but now I cannot get the motor to turn, no matter what I try. All the info I have is how to change the speed an...
-
I own Juki 1508s . GOLDSTAR GSM550 will not let me go lower than 1600 RPM. I have speed reducer installed. This model uses a needle positioner that I like. Question- need a new motor that allows RPM 500- 3500 but also has needle positioner that fits Juki AMCO shaft. ( see picture of needle...
-
My JUKI came with a Goldstar GBSM 500 servo motor. I lost the instructions of what the buttons do. One is speed, one says allows you to switch between P1 and P2 ?? I thought that was part of the positioned mechanism but nothing changers when I use it, third but allows change from F1,F2,F3. I don’t...
-
Hi all, I have a consew 226R and I'm ready to put a servo motor on it for more control. My problem is that most of the recommended motors on leather forums, like the Reliable motors (which seem reasonable for well under $200au), are all for sale overseas or on ebay. Whilst some of them look li...
-
Hello, I’m having such an annoying problem with my “JACK JK-513A” servo engine. The engine is connected to my “JUKI DDL-8700”. So here’s the issue: The engine won’t go any faster than 02 in speed... Even though the speed is set to 20-30. Everything worked fine just the other day. Toda...
-
Hi all, I am trying to install a zeromax speed reducer i bought onto a juki ddl8700 with servo motor for some fine tune sewing of curved in tight spaces on small objects of leather and other thich fabric. Could anyone help me in figuring out how it is to be mounted/installed? I can grasp the...
-
I have just purchased a Juki DU-1181-N industrial sewing machine from Meissner Sewing in Sacramento. I have replaced the servo motor that it came with and replaced it with another that I already had. I am offering it for sale for $100 plus freight. Brand new. FSM-550 Servo Motor, POW 550W, 110V...
-
Long story, but here's the quasi short version ... Always been a hobby craftsman, wood work, welding and metal fabrication, electrical, plumbing, ranch construction, tractors, and a little sewing on the side ... etc. etc. I grew weary with a cheap Brother machine after repair and tuned ups, mov...
-
I'm in need of a 'slow' sewingmachine for precision and control stitching and found a good deal now. The advertiser send me this photo of the motor; it's a clutch motor, he called it a 'leather motor' since it goes at about 1425 r.p.m. I have no experience with motors/electronics and could use some...
-
Hi everyone new here and just became a proud owner of a consew 206! i quickly found out that it vibrates my entire apartment though, which isn’t great for neighbors. Im wondering if there are any servo motors with speed variability in the $100 range that would serve me well. Is that...
-
I've got a few different servo motors from the cheaper end of what's commonly available. However, as impressive as most of them may be, and as perfectly fine for garment machines as I'm sure they are, they all seem to be lacking something or several things, for my purposes. Mostly these are a limite...
-
hey folks, I have looked at most of the treads on servo motors, most thread are a few years old. Just wondering what people are currently recommending for servo motors. I am looking for good torque at lower speeds for thicker leather. I will be sewing layers 1/2 thick, but will also need to se...
-
Hello, everyone! I recently bought myself a Pfaff 345 cylinder bed industrial sewing machine. I would like to swap the fast 3F clutch motor with a more controllable servo motor. I live in Europe (Slovenia) and as far as I know I can't get my hands on a Family sew or Hightex motor he... -
Hello, I need a sewing machine and I would prefer to buy a vintage industrial (or near-industrial) model over the Sailrite LSZ, which is the obvious option for a new machine. I'll be doing mostly marine canvas, upholstery and sail repair, not as much with leather but you guys seem to be the exp...
-
I am new to the site and have been enjoying reading and researching. You folks are so knowledgeable and talented! I recently purchased a great industrial which has all the features I wanted..except the speed demon clutch motor. Does anyone have a recommendation as to where to order a good...
-
Does anyone know a source for a small motor pulley that will fit a Rex 550w Servo? I recently installed Rex servos on a Consew 226 and a Consew 206RB-1, and the new motors came with 3" pulleys. As expected, they ran a little faster than I wanted so I went shopping for some smaller motor pulley...
-
Hi guys- i need some recommendations on a servo motor for my DA 269-373. I have an Enduro Pro 5000rpm on my Consew 206rb, along with a speed reducer. It's a 110v motor, and I'd really like to do something similar on my other machine as well. However, I'm having trouble locating another motor li...
-
Hi there, I have a flatbed heavy-duty Sailrite LSZ-1 that I've been playing with and I've found the speed very difficult to control solely by the foot pedal. Looking at videos on youtube, I learned that Servo motors can be bought to retrofit old sewing machines, I wonder if I can do the same wi...
-
I'm selling my Cobra NP-4 skiver with servo motor, including table with wheels for $1,000 or best offer. I would keep it but unfortunately, I need to make room in my already-too-small apartment for the upcoming arrival of our first son. I've only used the skiver 3 or 4 times, for a total of less th... -
Hello Everyone! My father surprised me with giving me his old Consew 230. He makes boots for a living and used this machine for sewing leather. Primarily for the welts and piping and he figured it would be good for my endeavors to sew lightweight leather purses and organizers as it can sew the... -
New in the box. I'm not interested in going through ALL this stuff I got or trying to sell it, but I will let this go before i move. I bought this over a year ago, but never took it out of the box. $100 + actual shipping (or pick it up, just as good) http://www.leathermachineco.com/shop/...
-
A few months ago, I purchased a used Juki LU-563 from a reputable sewing machine seller in Atlanta, GA. The sewing machine, Consew analog servo motor, and table are all in great working order. There are plenty of online resources that helped me learn the machine and get started. After getting the...
