Jump to content

DieselTech

Members
  • Posts

    1,633
  • Joined

  • Last visited

Everything posted by DieselTech

  1. Nice work! Looks great! A nice rainbow of colors in there. It looks Sharp.
  2. This is how it is sewing with that left presser foot not touching the needle plate. Here is a couple pics. The side with the makers mark is the feed dog needle plate side. Might need to lower my feed dog a touch more & back foot pressure off some. What's your guys thoughts?
  3. Thanks. I think alot of guys & gals use the suede for lining. 1 high end holster maker uses it, so it cant be that bad.
  4. Nice work! They look great! Beautiful work. Do you line your scabbards & if so what do you use? Thanks.
  5. Thanks @Wizcrafts . I changed to @Patrick1 #25 needle plate & feed dog. I also changed the presser feet to the narrow foot & left presser foot. Should my presser foot be off of the needle plate? Here is a pic. Is there another adjustment I need to make? Thanks. Any & all help will be appreciated.
  6. Yeah I set the #25 needle plate & feed dog up using a leather machine co. procedure for the cobra class 4 for the standard needle plate & feed dog. I just did not know since i was using a aftermarket needle plate & feed dog if there were other/more critical adjustments not mentioned or showed.
  7. Guys & gals I recently recieved a new cobra class 4. I would like to install the #25 needle plate & feed dog. What adjustments need to be made? Is there a actual # for the feed dog height above the needle plate? Videos I watched said a papers thickness above the needle plate is the proper feed dog height. Can somebody give me some pointers to make sure everything is ok & I'm not going to break something. Thanks.
  8. Thanks. For the tip. I would have never thought about that. I will go ahead install it, then it wont get lost.
  9. Thanks TomE I appreciate it. Yeah I watch like 50 videos & read 14 articles & could not find anything on it for the class 4. I'm going to run without it then. Thanks.
  10. Guys & gals I'm assembling my cobra class 4. Where does this screw in thread guide go? It was in with a bag of parts. I cant seem to find anything about it. Now lmao I havent looked in the manual yet for it. I found 1 spot on top of the sewing machine it threads into, I just dont know if that is where it goes. The other thing is, if it is used what's it used for? & how is thread routed thru it? Thanks.
  11. Yeah I finally found a video by Van Plew on youtube about cobra class 4 eps installation. On another note I got a thread in thread guide I'm not sure as to where it goes. I found 1 spot right on top it threads into. Lmao I just dont know if it goes there. I cant find anything about it.
  12. Guys & gals my EPS directions got accidentally taped on the inside of the box & destroyed them when I opened the box. Does my EPS look like everything is installed right? The red Mark's were there from leather machine co. So I just lined them up. Does this look correct? Thanks.
  13. Now I remember it. But I dont remember where the actual brake is. & how you disable it or back it off. Thanks.
  14. Yeah I was going to get a cowboy cb4500, but the shipping was going to be twice as much than the cobra. So I went that route. I cant wait to use it. Lol I might get it put together tonight.
  15. Lmao I dont even know if mine is right! The bracket the drop down guide came with is goofy like yours & I could not get it to work. Soo them pics is how I mounted my guide.
  16. Thanks. I'll keep you updated. I'll get some pics here in a bit.
  17. Here how my drop down guide is mounted. I did buy the extended hand lift knob & bracket to make this all work.
  18. Thanks. I appreciate the photos. I'm slowly figuring it out.
  19. Yes it is. Lol I'm kinda lost at the moment. Trying to figure everything out. I'm trying to figure my EPS out now. Lmao I have seen a couple videos & it's got me kinda lost. But I think I'm right. Waiting on a phone call to make sure. Love it!!!
  20. Yep I watched a bunch of videos & they all said the same thing as you. Thanks. Well it showed up! Pallet full of stuff! Cant wait to try it out.
  21. My class 4 should be the same mounting for the drop down guide. I'll get you some pics once I get to that point.
  22. Welcome to the group. Bunch of great people here. Enjoy!
  23. Well I am supposed to take delivery of a cobra class 4 sewing machine in the morning. I'll keep you all posted. Hopefully I can find some help to set it all up.
  24. Nice work! They look great. I thought I was the only 1 carrying the old style Gerber multi-pliers. I carry the black oxide version.
  25. Yeah I want to make a PID knife oven as well, just had not really had the funds. Them good PID controllers are not cheap.
×
×
  • Create New...