Jump to content

billybopp

Members
  • Posts

    1,907
  • Joined

  • Last visited

Everything posted by billybopp

  1. Talk the gun maker into introducing a hammerless model.
  2. I think a lot of us on here have been sniffin' the same glue. It's a wonderful thing to be able to do something that you love. Good luck with your new endeavo(u)rs. Bill PS ... Hope you liked my little bit of English language humo(u)r.
  3. I'd try the dyes and stains on some scrap. If it works, it works. The super sheen or other finishes, I'd replace. Bill
  4. Looks like an edge beader to me. One "blade" follows down the edge of the leather, the other cuts a fine decorative line down the face of the leather. Bill
  5. I used to buy laser transparency film by the case in my old job at a school. Just be absolutely certain that it is laser film and do NOT mix it with any other. Others can melt in the fuser section of the printer. The occasional professor that brought in his own film and threw it into one of our printers cost us a lot of money in repairs. Markers for transparency film can be had in dry erase, wet erase, and permanent varieties, as well as in various line thicknesses. If I remember correctly, the Expo Vis-A-Vis brand fine point markers are more medium thickness. Staedtler brand markers were the finest points that I came across for transparency markers. Write on film is usually considerably thinner, and would probably trace better on leather but would melt in a laser printer, and smear in an inkjet. Inkjet film will also melt in a laser printer, and has a slight tooth to hold onto the ink. Be sure you print on the right side for most inkjet films. Hope that helps Bill
  6. Congratulations Bob! ... And thank you many times over for sharing your knowledge with us here. Bill
  7. When I spray resolene, or any other acrylic, I clean the airbrush with a mixture of water, a little white vinegar, and a few drops of dish detergent. That's a formula that somebody here on LWN suggested and it seems to work well ( I apologize, I don't remember who) . I follow up by disassembling the airbrush and cleaning it in an ultrasonic cleaner ... The ultrasonic is probably overkill, but hey. I already had the cleaner, might as well use for something other than cleaning jewelry once a year ! Bill
  8. I bet it makes a nice all-round table top. Totally jealous now. Then again, I doubt that HDPE would make a great kitchen floor ... which is about the only place that's got that much exposed floor here! Bill
  9. To give you some idea of what goes into fitting ... https://www.youtube.com/watch?v=ONZbrTW576A Needless to say, a flip-flop, sandal or shoe would likely have some measurements that would be different from these (such as placement of the toe-thong in a flip-flop), there would also be much that's alike. Bill
  10. I'll put my money on computer generated image that's then CNC'd or lasered onto a plate. The equipment to do the job is expensive, so initial outlay for that sort of thing would be high, but the materials and usage after that are relatively cheap so it would probably be economical to do one-off designs that way. Bill
  11. That's a good looking design, and the dye fade in looks great with it . The only thing I see that might need some attention is the sewing machine foot marks along the stitch line. I'm no sewing machine expert, but it looks as though the presser foot tension might be too great. Perhaps one of our sewing machine experts can chime in on that with a little more info. Hope that helps Bill
  12. Doing the math is often the way to go, but sometimes the practical - simple approach is best! It reminds me of a story that I've heard, but cannot say if it is fact or fiction. Thomas Edison came across one of his engineers hard at work with pencil and paper looking at the glass globe part of the prototype light bulb that was sitting in front of him. When asked what the engineer was doing he replied that he was trying to calculate the volume of the bulb. Edison grabbed the glass globe, filled it with water and drained it into a graduated cylinder and told the engineer "There's your answer". Bill
  13. It's a pyro r200 pyrography tool, or at least that's what the video shows. He is burning the design into the leather, similar to woodburning. http://www.creavea.com/pyrograveur-multifonction-basse-tension-pyrographe-r200_boutique-acheter-loisirs-creatifs_11076.html Bill
  14. I'm rather fond of this tool chest that's recently been on Sheridan's website, and given a bit of thought to building something similar. http://www.sheridanleather.com/Set_of_10_C_S_Osborne_Single_Hole_Punches_p/dt-000.htm Bill
  15. Most people have to keep a close watch on their bags in airports so that they aren't stolen for the contents. YOU may have to keep an close watch on your bags, or you may find contents left behind and bags gone! (Just sayin' ) Bill
  16. Well done, as always with your work. It does give entirely new meaning to the phrase "pull my finger", tho. Bill
  17. Thread arrived today. It looks quite nice, the colors are really vibrant, and I can't wait to try it out. Thank you!! Bill
  18. I sometimes use a plane for skiving belts. It works great. Bill
  19. You may want to check out this pinned item here on LWN. http://leatherworker.net/forum/index.php?showtopic=18101 It does a great job explaining edge burnishing, using saddle soap. Bill
  20. You might take a look at cuir boulli, or boiled leather if you want really stiff. There are several threads on here, and elsewhere. Bill
  21. Yeah ... Bandaids can get pretty expensive. The closest I've come to cut prevention is: http://www.amazon.com/CUTShield-Classic-Kitchen-Resistant-Contact/dp/B003DZ02MU/ref=sr_1_2?ie=UTF8&qid=1433643477&sr=8-2&keywords=kevlar+glove They do work ... when I remember to wear them. They are a little slicker than I'd like, but they do now make versions with latex palms, or PVC dots. I'll have to try them sometime. Bill
  22. Hmmm.. I never would have thought to use thread! Great tips. Thanks! Bill
  23. Really nice on both pieces. I'm particularly fond of the messenger bag, it's a nice beefy design. I really like the colors of they dye and hardware. Well done! Bill
  24. I like it! I'm assuming the yellow is acrylic paint .. If so, you may want to put on a coat of white first, as a base coat. Yellow is notorious for it's transparency. Bill
  25. There's a good example in Al Stohlman's "The Art of Hand Sewing Leather" on how to make a cylinder. Describing it without photos is a bit beyond my ability to type, but it's not all that hard to do. I've made many can kozi's using the technique. Bill
×
×
  • Create New...